角向倾斜缝处理机匣对压气机性能的影响

推进技术 ›› 2018, Vol. 39 ›› Issue (6): 1260-1266.

角向倾斜缝处理机匣对压气机性能的影响

张皓光¹,安康¹,楚武利^1,2,谭锋¹,张旭东¹

西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072; 先进航空发动机协同创新中心，北京 100191,西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072

发布日期:2021-08-15
作者简介:张皓光，男，博士，副教授，研究领域为叶轮机械气动热力学。E-mail: zhg@nwpu.edu.cn 通讯作者:安康，男，硕士生，研究领域为叶轮机械气动热力学。
基金资助:
国家自然科学基金重点项目(51536006)；国家自然科学基金(51006084)；航空科学基金(2014ZB53014)；

Effects of Blade-Angle Skewed Slots Casing Treatment on Compressor Performance

School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China,School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China,School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China;Collaborative Innovation Center of Advanced Aero-Engine，Beijing 100191，China,School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China and School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China

Published:2021-08-15

摘要/Abstract

摘要： 为了揭示角向缝、角向倾斜缝处理机匣对压气机性能及其流场的影响，采用试验与非定常数值模拟的方法针对一亚声轴流压气机进行了研究。结果表明，角向缝、角向倾斜缝处理机匣(前移)对应的综合裕度改进量分别为12.16%，39.60%；角向倾斜缝处理机匣的扩稳能力更强，且峰值等熵效率损失降低了约75%。通过详细地分析压气机叶顶流场表明，角向倾斜缝处理机匣能够将叶顶间隙泄漏流在膨胀扩散之前基本完全吸除，通道内几乎没有低速堵塞区出现，因而扩稳效果更好。同时从角向倾斜缝中喷射入叶顶前缘的气流径向分速较低，其与主流的相互作用较弱，故流动损失减小，等熵效率更高。

关键词: 角向倾斜缝；轴流压气机；间隙泄漏流；失速裕度；等熵效率

Abstract: In order to reveal the effects of blade-angle slots and blade-angle skewed slots casing treatment on the compressor’s performance and flow-field， a subsonic axial-flow compressor was studied by means of experiment and unsteady numerical simulation. The results show that the stall margin improvement is 12.16% and 39.60% for the blade-angle slots and blade-angle skewed slots casing treatment (move forward) respectively. The ability to improve stall margin is stronger， and the loss of peak isentropic efficiency is lower about 75% for the blade-angle skewed slots casing treatment. The detail analysis of compressor tip flow-field indicates that the tip clearance leakage flow is basically completely sucked before expansion and diffusion， and the low speed blockage area almost disappears in the tip blade passage. So the effect of stability enhancement is better for the blade-angle skewed slots casing treatment. At the same time， the radial velocity of the airflow becomes lower injected into the leading edge of the tip blade from blade-angle skewed slots， the interaction between injected flow and blade tip mainstream is weaker. Therefore the flow loss is reduced， and the isentropic efficiency is improved for blade-angle skewed slots casing treatment.

Key words: Blade-angle skewed slots；Axial-flow compressor；Clearance leakage flow；Stall margin；Isentropic efficiency

张皓光,安康,楚武利,谭锋,张旭东. 角向倾斜缝处理机匣对压气机性能的影响[J]. 推进技术, 2018, 39(6): 1260-1266.

ZHANG Hao-guang¹,AN Kang¹,CHU Wu-li^1,2,TAN Feng¹,ZHANG Xu-dong¹. Effects of Blade-Angle Skewed Slots Casing Treatment on Compressor Performance[J]. Journal of Propulsion Technology, 2018, 39(6): 1260-1266.

参考文献

[1] Aamir Shabbir, John J Adamczyk. Flow Mechanism for Stall Margin Improvement due to Circumferential Casing Grooves on Axial Compressors[R]. ASME GT 2004-53903.
[2] 楚武利, 卢新根, 吴艳辉. 带周向槽机匣处理的压气机内部流动数值模拟与试验[J]. 航空动力学报, 2006, 21(1): 100-105.
[3] Martin W Muller, Christoph Biela, Heinz-Peter Schiffer, et al. Interaction of Rotor and Casing Treatment Flow in an Axial Single-Stage Transonic Compressor with Circumferential Groove[R]. ASME GT 2008-50135.
[4] Victor Mileshin, Igor Brailko, Andrew Startsev. Application of Casing Circumferential Grooves to Counteract the Influence of Tip Clearance[R]. ASME GT 2008-51147.
[5] Kwang-Jin Choi, Jin-Hyuk Kim, Kwang-Yong Kim. Design Optimization of Circumferential Casing Grooves for a Transonic Axial Compressor to Enhance Stall Margin [R]. ASME GT 2010-22396.
[6] Osborn W M, Lewis G W, Heidelberg L J. Effect of Several Porous Casing Treatments on Stall Limit and on Overall Performance of an Axial Flow Compressor Rotor[R]. NASA TN D-6537, 1971.
[7] Moore R D. Effect of Ceasing Treatment on Overall and Blade Element Performance of a Compressor Rotor[R]. NASA TN D-6538, 1971.
[8] 刘志伟. 缝式机匣处理的若干观察和机理探索[M]. 西安:西北工业大学出版社, 1985.
[9] Wilke I, Kau H P. A Numerical Investigation of the Flow Mechanisms in a HPC Front Stage with Axial Slots[R]. ASME GT 2003-38481.
[10] Xingen Lu, Wuli Chu, Junqiang Zhu. Experimental and Numerical Investigation of a Subsonic Compressor with Bend Skewed Slot Casing Treatment[R]. ASME GT 2006-90026.
[11] Florian C, Danner, Hans-Peter Kau. Experimental and Numerical Analysis of Axial Skewed Slot Casing Treatments for a Transonic Compressor Stage[R]. ASME GT 2009-59647.
[12] 张皓光, 楚武利, 吴艳辉, 等. 轴向倾斜缝机匣处理影响压气机性能的机理[J]. 推进技术, 2010, 31(5): 555-561. (ZHANG Hao-guang, CHU Wu-li, WU Yan-hui, et al. Investigation of the Flow Mechanisms of Affecting Compressor Performance with Axial Skewed Slots Casing Treatment[J]. Journal of Propulsion Technology, 2010, 31(5): 555-561.)
[13] 张皓光, 谭锋, 楚武利, 等. 反叶片角向缝机匣处理影响轴流压气机性能的机理[J]. 航空动力学报, 2016, 31(10): 2387-2394.
[14] Ning Ma, Xi Nan, Feng Lin. Numerical Study on Effects of Axial-Slot Casing Treatment on Peak Efficiency of Axial Compressor[R]. ASME GT 2016-56554.
[15] 张皓光. 轴流压气机机匣处理的试验与数值研究[D]. 西安:西北工业大学, 2008.
[16] 张皓光, 安康, 吴艳辉, 等. 周向槽轴向位置影响机匣处理扩稳能力的机理[J]. 推进技术, 2016, 37(12): 2296-2302. (ZHANG Hao-guang, AN Kang, WU Yan-hui, et al. Mechanism of Affecting Ability of Casing Treatment to Improve Stall Margin with Varying Axial Position of Circumferential Grooves[J]. Journal of Propulsion Technology, 2016, 37(12): 2296-2302.)(编辑:梅瑛)　　　　　　　　　　　　　*　收稿日期:2017-06-06；修订日期:2017-07-14。基金项目:国家自然科学基金重点项目(51536006)；国家自然科学基金(51006084)；航空科学基金(2014ZB53014)；陕西省自然科学基金(2015JM5202)。作者简介:张皓光,男,博士,副教授,研究领域为叶轮机械气动热力学。E-mail: zhg@nwpu.edu.cn通讯作者:安康,男,硕士生,研究领域为叶轮机械气动热力学。E-mail: 1021704238@qq.com