基于马赫线切割的楔形乘波前体改进设计研究

推进技术 ›› 2018, Vol. 39 ›› Issue (8): 1696-1702.

基于马赫线切割的楔形乘波前体改进设计研究

吕宇超,胡姝瑶,蒋崇文

北京航空航天大学航空科学与工程学院，北京 100191,北京航空航天大学航空科学与工程学院，北京 100191,北京航空航天大学航空科学与工程学院，北京 100191

发布日期:2021-08-15

Improved Design of Wedge-Derived Waverider Forebody Based on Mach Line Cutting of Compression Surfaces

School of Aeronautic Science and Engineering，Beihang University，Beijing 100191，China,School of Aeronautic Science and Engineering，Beihang University，Beijing 100191，China and School of Aeronautic Science and Engineering，Beihang University，Beijing 100191，China

Published:2021-08-15

摘要/Abstract

摘要： 为了改善楔形乘波前体两侧大下反角对其横航向静稳定性的不利影响，利用马赫线切割方法对其进行了改进设计。该方法为在不影响进气道入流的条件下，对前体预压缩面的改进提供了基础。通过斜激波关系式求出了后掠斜楔激波脱体的临界参数，将其应用于楔形乘波前体的改进，使改进后的外形仍具有乘波特性。使用以上方法对典型楔形乘波前体开展了改进设计，采用数值模拟方法对改进外形进行计算分析。结果表明无粘流场中进气道入流区域的流场与原楔形乘波前体完全一致，无粘升阻比有所提高；同时，改进外形的横航向静稳定性与原楔形乘波体相比有明显改善。粘性数值模拟结果显示改进外形在有粘条件下仍具有较好的乘波特性和升阻比。

关键词: 乘波前体；马赫线切割；进气道流动；改进设计

Abstract: In order to improve the detrimental impact on lateral static stability caused by the large negative-dihedral angle of the wedge-derived waverider forebody， the improved design based on the Mach Line Cutting of Compression Surfaces (MLCCS) was developed. The MLCCS principle provided the basis for improving the compression surfaces of the inlet without affecting the inlet flow. The critical parameters for the shock wave detached from the leading edge of swept wedges were obtained by the oblique shock equations. And the parameters were used in the improved design to guarantee the attached shock wave. The improved waverider forebody was designed and numerical simulations were taken. The inviscid results show that the uniform pre-compression inflows provided by the wedge-derived and the improved waverider forebodies are identical， and the lift-to-drag ratio increased. The lateral static stability of the waverider forebody gets an effective improvement. And the shock is still attached to the leading edge of the improved waverider forebody. The viscous results indicate that the improved waverider forebody still have higher lift-to-drag ratio than the wedge-derived waverider forebody， and the shock is just detached from the leading edge for a short distance.

Key words: Waverider forebody；Mach line cutting of compression surfaces；Inlet flow；Improved design

吕宇超,胡姝瑶,蒋崇文. 基于马赫线切割的楔形乘波前体改进设计研究[J]. 推进技术, 2018, 39(8): 1696-1702.

LV Yu-chao,HU Shu-yao,JIANG Chong-wen. Improved Design of Wedge-Derived Waverider Forebody Based on Mach Line Cutting of Compression Surfaces[J]. Journal of Propulsion Technology, 2018, 39(8): 1696-1702.

参考文献

[1] Witte D W, Huebner L D, Trexler C A, et al. Propulsion Airframe Integration Test Techniques for Hypersonic Airbreathing Configurations at NASA Langley Research Center[R]. AIAA 2003-4406.
[2] Berens T M, Bissinger N C. Forebody Precompression Effects and Inlet Entry Conditions for Hypersonic Vehicles[J]. Journal of Spacecraft and Rockets, 1998, 35(1): 30-36.
[3] O'Neill M K L, Lewis M J. Optimized Scramjet Integration on a Waverider [J]. Journal of Aircraft, 1992, 29(6): 1114-1121.
[4] 朱伟, 张堃元, 南向军. 壁面马赫数分布规律可控的新型内收缩基准流场设计方法[J]. 推进技术, 2013, 34(4): 433-438. (ZHU Wei, ZHANG Kun-yuan, NAN Xiang-jun. Investigation on Basic Flow-Field with Controlled Mach Number Gradient for Hypersonic Inward Turning Inlets[J]. Journal of Propulsion Technology, 2013, 34(4): 433-438.)
[5] 贺旭照, 周正, 倪鸿礼. 密切内锥乘波前体进气道一体化设计和性能分析[J]. 推进技术, 2012, 33(4):510-515. (HE Xu-zhao, ZHOU Zheng, NI Hong-li. Integrated Design Methods and Performance Analyses of Osculating Inward Turning Cone Waverider Forebody Inlet[J]. Journal of Propulsion Technology, 2012, 33(4):510-515.)
[6] Nonweiler T R F. Aerodynamic Problems of Manned Space Vehicles[J]. Journal of the Royal Aeroanutical Society, 1959, 63: 521-528.
[7] Flower J W. Configurations for High Supersonic Speeds Derived from Simple Shock-Waves and Expansions[J]. Journal of the Royal Aeronautical Society, 1963, 67:287-290.
[8] Pike J. On Lifting Surfaces Supporting One or More Plane Shock Waves[R]. Royal Aircraft Establishment, 66-3623, 1966.
[9] Towned L H. On Lifting Bodies Which Contain Two-Dimensional Supersonic Flows[R]. Royal Aircraft Establishment 63-2675, 1963.
[10] Tarpley C. The Optimization of Engine-Integrated Hypersonic Waveriders with State Flight and Static Margin Constraints[D]. Maryland: University of Maryland, 1995.
[11] Rudd L E, Pines D J. Dynamic Control of Mission Oriented Hypersonic Waveriders[R]. AIAA 99-4951.
[12] Jiang C W, Hu S Y, Gao Z X, et al. Mach Line Cutting of Compression Surface for Two-Dimensional Planar Inlets[J]. AIAA Journal, 2017, 55(1): 1-8.
[13] Neal D D. General Three-Dimensional Relation for Oblique Shocks on Swept Ramps[J]. AIAA Journal, 2016, 54(1): 310-319.
[14] Gao Z X, Lee C H. A Numerical Study of Turbulent Combustion Characteristics in a Combustion Chamber of a Scramjet Engine[J]. Science China Technological Sciences, 2013, 53(8): 2111-2121.
[15] Gao Z X, Jiang C W, Pan S W, et al. Combustion Heat-Release Effects on Supersonic Compressible Turbulent Boundary Layers[J]. AIAA Journal, 2015, 53(7): 1949-1968.　　　　　　　　　　　　　*　收稿日期:2017-06-29；修订日期:2017-08-18。通讯作者:吕宇超,男,博士生,研究领域为高超声速飞行器设计。E-mail: buaa_lyc@126.com(编辑:史亚红)