燃油流量对气冷喷油杆性能影响的数值研究

推进技术 ›› 2018, Vol. 39 ›› Issue (9): 2020-2027.

燃油流量对气冷喷油杆性能影响的数值研究

刘友宏,郭佳

北京航空航天大学能源与动力工程学院，北京 100191,北京航空航天大学能源与动力工程学院，北京 100191

发布日期:2021-08-15

Numerical Analysis for Effects of Fuel Mass Flow Rate on Performance of Air-Cooled Fuel Injectors

School of Energy and Power Engineering，Beihang University，Beijing 100191，China and School of Energy and Power Engineering，Beihang University，Beijing 100191，China

Published:2021-08-15

摘要/Abstract

摘要： 以涡扇发动机加力燃烧室气冷喷油杆与隔热套为研究对象，分析燃油流量对气冷喷油杆和隔热套温度分布的影响，对其在巡航状态下进行了流热固耦合三维数值模拟研究，考虑了燃气、空气的多组分流动，以及燃油和燃气的两相流动。结果表明:随着燃油流量从0.01kg/s增加到0.07kg/s，两根喷油杆(P1和P2)平均温度下降4.6%，隔热套的平均温度下降2.8%；燃油在喷油杆下部流动速度过低，造成其下部温度较其他部分明显偏高，随着燃油流量而逐渐增加而改善；外涵冷气进入隔热套中的流动方向影响了喷油杆的温度分布；冷气从一号喷油杆侧的出口中流出的比例占到进入隔热套总冷气流量的60%左右，因此一号喷油杆的喷嘴温度比二号喷油杆的喷嘴温度低4%～7%。

关键词: 气冷喷油杆；耦合数值模拟；燃油流量；两相流

Abstract: Based on an air–cooled fuel injector in an afterburner of a turbofan engine， the temperature distribution was investigated under the influence of different fuel mass flow rates. A three-dimensional heat-liquid-solid coupling numerical simulation was conducted on the cruise state considering the multicomponent flow of combustion gas and air as well as the two-phase flow of fuel and combustion gas. The results indicate that when the fuel mass flow rate increases from 0.01kg/s to 0.07kg/s， average temperature of injectors (P1 and P2) and the heat shield decrease 4.6% and 2.8%， relatively lower fuel flow velocity leads to higher fuel temperature in the lower part of fuel injector P1， the temperature becomes homogeneous obviously as the increasing of fuel mass flow rate. The flow direction of cold air in the heat shield affects the temperature of fuel injectors observably. About 60% cold air flows out from the holes around the nozzles on the fuel injector P1， which causes the nozzles temperature 4%～7% lower than that of fuel injector P2.

Key words: Air-cooled fuel injectors；Coupling numerical simulation；Fuel mass flow rate；Two-phase flow

刘友宏,郭佳. 燃油流量对气冷喷油杆性能影响的数值研究[J]. 推进技术, 2018, 39(9): 2020-2027.

LIU You-hong,GUO Jia. Numerical Analysis for Effects of Fuel Mass Flow Rate on Performance of Air-Cooled Fuel Injectors[J]. Journal of Propulsion Technology, 2018, 39(9): 2020-2027.

参考文献

[1] 孙雨超, 张志学, 李江宁, 等. 一体化加力燃烧室方案设计及数值研究[J]. 航空科学技术, 2011, (4):71-74.
[2] 李锋, 郭瑞卿, 李龙贤, 等. 整流支板和火焰稳定器的一体化设计加力燃烧室性能的数值模拟[J]. 航空发动机, 2012, (5): 6-9.
[3] Carrier D, Champlain A D, Bardon M. Direct Fuel Injection for Bluff Body Flame Stabilization[C]. Sacramento: Joint Propulsion Conference and Exhibit, 2006.
[4] Xiao Yumin, Amano R. A Study on Effective Heat Transfer Characteristics in an Afterburner with Ceramic Stabilizer[C]. Grapevine, Texas: Aerospace Sciences Meeting and Exhibit, 2013.
[5] 郭成富, 王勇, 曹康. 加力燃烧室喷油杆结焦试验研究[J]. 燃气涡轮试验与研究, 1997, 10(1): 26-31.
[6] Peat A E. Thermal Decomposition of Aviation Fuel[C]. London: ASME 1982 International Gas Turbine Conference and Exhibit, 1982.
[7] 贾春燕, 王洪铭. 航空发动机燃烧室喷嘴内部燃油结焦研究[J]. 航空发动机, 2011, 37(5): 41-44.
[8] 张孝春, 孙雨超, 刘涛. 先进加力燃烧室设计技术综述[J]. 航空发动机, 2014, 40(2): 24-30.
[9] 袁立公, 邓宏武, 徐国强, 等. 超临界压力下航空煤油RP-3壁面结焦特性对换热的影响[J]. 航空动力学报, 2013, 28(4): 832-837.
[10] 李建中, 袁丽, 尚伟, 等. 高温升燃烧室喷油杆热防护试验研究[J]. 推进技术, 2016, 37(12): 2336-2342. (LI Jian-zhong, YUAN Li, SHANG Wei, et al. Experimental Investigation on Thermal Protection for Fuel Injector Pole of High Temperature Rise Combustor[J]. Journal of Propulsion Technology, 2016, 37(12): 2336-2342.)
[11] 徐志刚, 刘贵才, 李权, 等. 某型发动机加力燃油总管喷油杆断裂分析[J]. 宇航材料工艺, 2002, (4): 58-61.
[12] 白兴艳, 张频捷, 岳连捷, 等. 加力用气冷与气动雾化喷油杆的性能研究[J]. 航空动力学报, 2000, 15(4): 391-396.
[13] 邢菲, 孟祥泰, 樊未军, 等. 气冷气动雾化喷油杆冷却性能实验[J]. 推进技术, 2007, 28(6): 612-615.(XING Fei, MENG Xiang-tai, FAN Wei-jun, et al. Experiments on Cooling Effect of the Air Atomizing Fuel Injector Bars[J]. Journal of Propulsion Technology, 2007, 28(6): 612-615.)
[14] 闫宝华, 樊未军, 杨茂林. 加力燃烧室双层喷油杆内冷却气流动特性[J]. 航空动力学报, 2008, 23(7):1182-1188.
[15] 刘友宏, 王晓博. 风兜面积对气冷喷油杆性能影响的数值研究[J]. 航空动力学报, 2016, 31(2): 337-344.
[16] 刘友宏, 周开福, 牛俊杰. 气冷喷油杆隔热套高度对混合扩压器性能影响[J]. 北京航空航天大学学报, 2016, 42(6): 1099-1106.(编辑:朱立影)　　　　　　　　　　　　　*　收稿日期:2017-08-27；修订日期:2017-10-12。通讯作者:刘友宏,男,博士,教授,博士生导师,研究领域为发动机气动热力学。E-mail: liuyh@buaa.edu.cn