齿型对压气机级间封严特性影响的实验研究

推进技术 ›› 2018, Vol. 39 ›› Issue (9): 2085-2093.

齿型对压气机级间封严特性影响的实验研究

孔晓治,刘高文,雷昭,畅然,刘阳

西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072

发布日期:2021-08-15

Experimental Investigation for Effects of Tooth Shapes on Compressor Inter-Stage Seal

School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China,School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China,School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China,School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China and School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China

Published:2021-08-15

摘要/Abstract

摘要： 为了对比不同齿型下压气机级间封严特性，对基准常规齿、直通针型齿、直通宝塔齿和台阶斜齿时的级间篦齿封严进行了实验研究。在压比1.05～1.30，转速0～8.1kr/min时对不同齿型的工作间隙、泄漏流量、风阻温升和出口盘腔的旋转比进行了测量。基准常规齿是级间最常用的篦齿结构，将其他三种齿型下级间封严的泄漏特性、温升特性和旋流特性与其进行对比。结果表明:随着齿顶间隙的增大，基准常规齿的流量系数先增大后减小，在间隙c=0.8mm附近有最大值；相同间隙时，台阶斜齿的封严效果最好，其流量系数比基准常规齿时小40%左右。直通针型齿、直通宝塔齿的封严效果略优于基准常规齿，三者相差不大；但是，泄漏流量越小，级间封严的温升和旋流越大。压比1.30时台阶斜齿与基准常规齿的温升比为1.5左右。另外，高转速时台阶斜齿比基准常规齿的旋转比大18%左右。

关键词: 级间封严；篦齿；旋转盘腔；流量系数；风阻温升；旋流

Abstract: To compare the performances of compressor inter-stage seal for different tooth shapes， the experiments were conducted at an inter-stage seal test facility for conventional straight-through， needlelike， tower-type and stepped and slanted labyrinth seals. Working tip clearances， leakage flow rates， windage heating and swirl ratios in the outlet cavity were measured at different pressure ratios (1.05～1.30) and different rotating speeds (0～8.1kr/min). The leakage behavior， windage heating characteristic and swirl characteristic of three new tooth shapes were compared with conventional straight-through labyrinth seal (the most used) in the current study. Results show that very small as well as very large tip clearances yield lower discharge coefficient [CD] values than medium clearances with a maximum around 0.8mm for conventional straight-through labyrinth seal. The stepped and slanted labyrinth seal has the best sealing capability and reduces discharge coefficient as much as 40% compared to conventional straight-through labyrinth seal. In addition， discharge coefficients of needlelike and tower-type straight-through labyrinth seals are slightly lower than the [CD]-values of conventional one. However， the reduction of leakage flow through the stator well leads to increases in the temperature rise and swirl velocity. The ratios of temperature rises between the stepped and slanted labyrinth seal and conventional straight-through labyrinth seal are around 1.5 at pessure ratio of 1.30. For high rotational speeds， the swirl ratios of stepped and slanted labyrinth seal are found 18% larger than that of conventional straight-through labyrinth seal.

Key words: Inter-stage seal；Labyrinth；Rotating cavity；Discharge coefficient；Windage heating；Swirl flow

孔晓治,刘高文,雷昭,畅然,刘阳. 齿型对压气机级间封严特性影响的实验研究[J]. 推进技术, 2018, 39(9): 2085-2093.

KONG Xiao-zhi,LIU Gao-wen,LEI Zhao,CHANG Ran,LIU Yang. Experimental Investigation for Effects of Tooth Shapes on Compressor Inter-Stage Seal[J]. Journal of Propulsion Technology, 2018, 39(9): 2085-2093.

参考文献

[1] Denecke J, Dullenkopf K, Wittig S, et al. Experimental Investigation of the Total Temperature Increase and Swirl Development in Rotating Labyrinth Seals[R]. ASME GT 2005-68677.
[2] 胡东旭, 贾力, 杨立新. 篦齿封严泄漏特性的实验[J]. 航空动力学报, 2014, 29(3): 549-555.
[3] David C J, Paul C I, John R T. Abradable Stator Gas Turbine Labyrinth Seals, Part 2: Numerical Modeling of Differing Seal Geometries and the Construction of a Second Generation Design Tool[R]. AIAA 2002-3937.
[4] Micio M, Facchini B, Innocenti L, et al. Experiment Investigation on Leakage Loss and Heat Transfer in a Straight Through Labyrinth Seal[R]. ASME GT 2011-46402.
[5] Mohammad Alizadeh, Behnam Nikkhahi. Numerical Study on the Effect of Geometrical Parameters on the Labyrinth-Honeycomb Seal Performance[R]. ASME GT 2014-25147.
[6] Paolillo R, Moore S, Cloud D, et al. Impact of Rotational Speed on the Discharge Characteristic of Stepped Labyrinth Seals[R]. ASME GT 2007-28248.
[7] 王鹏飞, 郭文, 张靖周. 旋转封严篦齿风阻温升的试验研究与数值分析[J]. 航空动力学报, 2013, 28(6): 1402-1708.
[8] 张勃, 吉洪湖, 杜发青, 等. 篦齿封严尺寸缩放与气流温度变化对流动与传热影响试验研究[J]. 推进技术, 2016, 37(2): 304-310. (ZHANG Bo, JI Hong-hu, DU Fang-qing, et al. Experimental Investigation of Scaling and Temperature Effects on Flowing and Heat Transfer Characteristics in Labyrinth Seals[J]. Journal of Propulsion Technology, 2016, 37(2): 304-310.)
[9] 纪国剑. 航空发动机典型篦齿封严泄漏特性的数值和实验研究[D]. 南京:南京航空航天大学, 2008.
[10] Sungho Yoon, Rudolf Selmeier, Patricia Cargill, et al. Effect of the Stator Hub Configuration and Stage Design Parameters on Aerodynamic Loss in Axial Compressors[J]. Journal of Turbomachinery, 2015, 137, (9).
[11] Wellborn S R, Tolchinsky I, Okiishi T H. Modeling Shrouded Stator Cavity Flows in Axial-Flow Compressors[J]. Journal of Turbomachinery, 2000, 122(1): 55-61.
[12] Wellborn S R. Details of Axial Ccompressor Shrouded Stator Cavity Flows[R]. ASME GT 2001-0495.
[13] Leo V L. In-Engine Measurements of Temperature Rises in Axial Compressor Shrouded Stator Cavities[R]. ASME 2002-GT-30245.
[14] 刘高文, 孔晓治, 陈凯, 等. 转动和旋流对压气机级间封严影响的数值研究[J]. 推进技术, 2014, 35(12): 1687-1693. (LIU Gao-wen, KONG Xiao-zhi, CHEN Kai, et al. Numerical Study for Effects of Rotation and Swirl on Labyrinth Sealing in a Compressor Stator Well[J]. Journal of Propulsion Technology, 2014, 35(12): 1687-1693.)
[15] 孔晓治, 刘高文, 雷昭, 等. 转速对压气机级间篦齿封严影响的实验[J]. 航空动力学报, 2016, 31(7):1575-1582.
[16] Wellborn S R, Okiishi T H. The Influence of Shrouded Stators Cavity Flows on Multistage Compressor Performance[J]. Journal of Turbomachinery, 1999, 121(3): 486-497.
[17] Sangan C M, Scobie J A, Owen J M. Performance of a Finned Turbine Rim Seal[J]. Journal of Turbomachinery, 2014, 136(11).
[18] 夏全忠. 直通型封严篦齿瞬稳态特性研究[D]. 西安:西北工业大学, 2012.
[19] 刘高文, 陈凯, 刚铁, 等. 压比和雷诺数对压气机级间篦齿封严流动特性的影响[J]. 航空动力学报, 2015, 30(7): 1554-1560.
[20] Xiaozhi KONG, Gaowen LIU, Yuxin LIU, et al. Investigation on the Leakage Flow, Windage Heating and Swirl Development of Rotating Labyrinth Seal in a Compressor Stator Well[R]. ASME 2016-GT-56740.(编辑:朱立影)　　　　　　　　　　　　　*　收稿日期:2017-08-18；修订日期:2017-10-30。通讯作者:孔晓治,男,博士生,研究领域为发动机空气系统和旋转盘腔中的流动传热。E-mail: