进口速度畸变以及涵道比对波瓣混合器性能影响的试验研究

推进技术 ›› 2019, Vol. 40 ›› Issue (2): 307-314.

进口速度畸变以及涵道比对波瓣混合器性能影响的试验研究

蔡明权,黄晓锋,邓恺,黄义勇,徐华胜

中国航发四川燃气涡轮研究院，四川成都 610500,中国航发四川燃气涡轮研究院，四川成都 610500,中国航发四川燃气涡轮研究院，四川成都 610500,中国航发四川燃气涡轮研究院，四川成都 610500,中国航发四川燃气涡轮研究院，四川成都 610500

发布日期:2021-08-15

Experimental Investigation on Performance of Lobed Mixer with Effects of Inlet Velocity Distortion and Bypass Ratio

AECC Sichuan Gas Turbine Establishment，Chengdu 610500，China,AECC Sichuan Gas Turbine Establishment，Chengdu 610500，China,AECC Sichuan Gas Turbine Establishment，Chengdu 610500，China,AECC Sichuan Gas Turbine Establishment，Chengdu 610500，China and AECC Sichuan Gas Turbine Establishment，Chengdu 610500，China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究不同进口速度畸变以及涵道比对波瓣混合器性能的影响规律，以带进口畸变孔板的双涵道全环轴对称加力模型试验件为研究对象，采用五孔探针配合三维位移机构测量了不同涵道比下波瓣混合器后的三维流场。试验研究表明:随着波瓣混合器出口距离的增加，内外涵掺混速度先升高后降低，总压恢复系数逐渐降低，混合效率和推力增益逐渐升高；随着混合器涵道比的增加，流向涡及低温区域范围增大，混合均匀性下降，混合效率和总压恢复系数均降低；进口畸变峰值在上方时，气流加速掺混对推力增益有益，总压恢复系数更高，小涵道比混合效率更高；进口畸变峰值在下方时，扩压段壁面静压和中心锥锥体静压均较高。

关键词: 加力燃烧室；波瓣混合器；进口速度畸变；涵道比；试验

Abstract: In order to figure out how the inlet velocity distortion and the bypass ratio effect on the performance of lobed mixer，a two-flow annular axisymmetric afterburner test model with inlet distortion orifice plates was designed and a five-hole probe combined with a three-dimensional displacement equipment was employed to measure the three-dimensional flow field of different inlet velocity distortion and bypass ratio behind lobed mixer planes. The results show that with the increases of distance from the outlet of lobed mixer，the mixing velocity of core and bypass will increase at first then descend，and the total pressure recovery coefficient will decline，while the mixing efficiency and thrust gain will increase. The results also show that the increases of bypass ratio will enlarge the range of streamwise vortex and low temperature，while the mixing homogeneity，mixing efficiency and total pressure recovery coefficient will decline. When the inlet velocity distortion peak is on the top，the airflow will be accelerated mixing which is beneficial to the thrust gain and the total pressure recovery coefficient will be higher，and the mixture efficiency will be higher with a small bypass ratio. When the peak of inlet velocity distortion is at the bottom，both the wall static pressure of diffuser and the static pressure of center cone are relatively high.

Key words: Afterburner；Lobed mixer；Inlet velocity distortion；Bypass ratio；Experiment

蔡明权,黄晓锋,邓恺,黄义勇,徐华胜. 进口速度畸变以及涵道比对波瓣混合器性能影响的试验研究[J]. 推进技术, 2019, 40(2): 307-314.

CAI Ming-quan,HUANG Xiao-feng,DENG Kai,HUANG Yi-yong,XU Hua-sheng. Experimental Investigation on Performance of Lobed Mixer with Effects of Inlet Velocity Distortion and Bypass Ratio[J]. Journal of Propulsion Technology, 2019, 40(2): 307-314.

参考文献

[1] Paterson R W. Turbofan Forced Mixer-Nozzle Internal Flowfield—A Benchmark Experimental Study[J]. NASA-CR-3492, 1982.
[2] Paterson R W. Turbofan Mixer Nozzle Flow Field—A Benchmark Experimental Study[J]. Journal of Engineering for Gas Turbines and Power, 1984, 106(3).
[3] Shumpert P k. An Experimental Model Investigation of Turbofan Engine Internal Exhaust Gas Mixer Configurations[R]. AIAA 80-0228.
[4] Presz Jr W M, Reynolds G, McCormick D. Thrust Augmentation Using Mixer-Ejector Diffuser Systems[R]. AIAA 2002-0020.
[5] 吴寿生, 侯志兴. 排气混合器和短舱[M]. 北京:航空工业出版社, 1991.
[6] Presz W M, Morin B K L, Gousy R G. Forced Mixer Lobes in Ejector Designs[J]. Journal of Propulsion and Power, 1988, 4(4): 350-355.
[7] Anderson B H, Povinelli L A. Factors Which Influence the Behavior of Turbofan Forced Mixer Nozzles[J]. NASA-TM-81668, 1981.
[8] Rowe R Kevin, Kuchar A P. Energy Efficient Engine—Scaled Mixer Performance Report(Final)[J]. NASA- CR-167947, 1982.
[9] Simon C M Yu, Yip T H, Liu C Y. The Mixing Characteristics of Forced Mixers with Scalloped Lobe[R]. AIAA 96-0117.
[10] 刘友宏, 张少鹏, 杨旭, 等. 波瓣尾缘切角对涡扇发动机混合排气系统气动热力性能影响[J]. 推进技术, 2013, 34(6): 734-740. (LIU You-hong, ZHANG Shao-peng, YANG Xu, et al. Effects of Cut Angles at Trailing Edge of Lobe on Aerothermodynamic Performance of Forced Mixing Exhaust System in Turbofan Engine [J]. Journal of Propulsion Technology, 2013, 34(6): 734-740.)
[11] 谢翌, 阮登芳, 钟晨, 等. 波瓣帽罩结构和脊线对混合排气系统性能影响[J]. 推进技术, 2014, 35(3): 314-319. (XIE Yi, RUAN Deng-fang, ZHONG Chen, et al. Effects of Lobe Cap and Crest Line on Performance of Mixing Exhaust System[J]. Journal of Propulsion Technology, 2014, 35(3): 314-319.)
[12] 金捷, 何家德, 徐镇勇, 等. 涡扇加力模型混合扩压器三维流场测量[J]. 燃气涡轮试验与研究, 1996, (2): 45-49.
[13] 张哲衡, 王东明, 张宝华, 等. 波瓣混合器流场试验[J]. 航空动力学报, 2014, 29(8): 1761-1768.
[14] 张晓东, 姜正礼, 赵旺东. 五孔探针在涡轮导向器出口流场测量中的应用[J]. 燃气涡轮试验与研究, 2010, 23(4): 44-48.
[15] 熊兵, 陈洪敏, 文壁, 等. 基于四孔压力探针技术的涡轮转子出口流场测量[J]. 燃气涡轮试验与研究, 2012, 25(1): 6-10.
[16] Kozlowski H, Larkin M. Energy Efficient Engine—Exhaust Mixers Model Technology Report[R]. NASA-CR-165459, 1981.
[17] 雷志军. 进口预旋条件下涡扇发动机波瓣射流掺混机理的实验研究[D]. 北京:中国科学院研究生院, 2011.
[18] 苏尚美, 雷志军, 岳巍, 等. 进口预旋条件下波瓣混合器强制掺混机理[J]. 推进技术, 2013, 34(2):230-239. (SU Shang-mei, LEI Zhi-jun, YUE Wei, et al. Mechanism of Forced Mixing for Lobed Mixer with Inlet Swirl[J]. Journal of Propulsion Technology, 2013, 34(2): 230-239.)　　　　　　　　　　　　　　收稿日期:2018-01-14；修订日期:2018-03-06。通讯作者:蔡明权,硕士,工程师,研究领域为加力燃烧室。E-mail: wocaimingquan@126.com(编辑:史亚红)