轮缘封严气流与主流涡系交互作用的非定常数值研究

推进技术 ›› 2019, Vol. 40 ›› Issue (2): 315-323.

轮缘封严气流与主流涡系交互作用的非定常数值研究

杨帆,周莉,王占学

西北工业大学动力与能源学院，陕西西安 710129,西北工业大学动力与能源学院，陕西西安 710129,西北工业大学动力与能源学院，陕西西安 710129

发布日期:2021-08-15
基金资助:
国家自然科学基金(51876176；51576163)。

Unsteady Numerical Investigation on Vortex Interaction Between Rim Seal Flow and Mainstream

School of Power and Energy，Northwestern Polytechnical University，Xi’an 710129，China,School of Power and Energy，Northwestern Polytechnical University，Xi’an 710129，China and School of Power and Energy，Northwestern Polytechnical University，Xi’an 710129，China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究涡轮转静盘腔中轮缘封严气流与主流的非定常涡系交互作用机制，在有无封严气流的工况下，数值模拟了封严气流对主流二次流的影响。结果表明，封严气流对上游静子的堵塞减弱了其轮毂二次流强度，并挤压静子轮毂二次流使得其径向位置降低而区域减小。静子轮毂二次流抑制了封严出流作用以及转子轮毂通道涡的径向扩张，并加剧转子轮毂二次流的总压损失。封严气流诱导形成了腔体诱导涡和剪切诱导涡，其中剪切诱导涡发展成为转子轮毂通道涡的主要组成部分。同时，封严气流通过剪切诱导涡的作用增加了转子轮毂二次流的径向位置和强度。由于转子和静子的相对运动，封严气流与主流的涡系交互作用呈现出明显的非定常变化。

关键词: 转静盘腔；封严气流；涡系；非定常；涡轮

Abstract: In order to investigate unsteady vortex interaction mechanisms between turbine rotor-stator cavity rim seal flow and mainstream， numerical investigations were conducted for effects of rim seal flow on the secondary flow of mainstream under the condition with and without rim seal flow. The results show that intensity of secondary flow of the stator is weakened due to the blockage effect caused by rim seal flow. In addition， the rim seal flow extrudes secondary flow of the stator and leads to decreasing radial location and area of secondary flow. Besides， the strength of egress flow and radial expansion of rotor hub passage vortex are restrained by hub secondary flow of the stator. The total pressure loss of hub secondary flow of rotor is strengthened by that of the stator. Cavity induced vortex and shear induced vortex are formed due to the induction of rim seal flow. The shear induced vortex is developed into the main part of rotor hub passage vortex. Furthermore， the radial location and intensity of hub secondary flow of the rotor is increased by the shear induced vortex. Due to relative rotation of the stator and rotor， vortex interaction between rim seal flow and mainstream is obviously unsteady.

Key words: Rotor-stator cavity；Egress flow；Vortex；Unsteady；Turbine

杨帆,周莉,王占学. 轮缘封严气流与主流涡系交互作用的非定常数值研究[J]. 推进技术, 2019, 40(2): 315-323.

YANG Fan,ZHOU Li,WANG Zhan-xue. Unsteady Numerical Investigation on Vortex Interaction Between Rim Seal Flow and Mainstream[J]. Journal of Propulsion Technology, 2019, 40(2): 315-323.

参考文献

[1] 张晶辉, 马宏伟. 轮缘封严气体对涡轮转子性能影响的非定常数值研究[J]. 推进技术, 2014, 35(4): 470-478. (ZHANG Jing-hui, MA Hong-wei. Unsteady Numerical Investigation for Effects of Rim Sealing Flow on Performance of a Turbine Rotor[J]. Journal of Propulsion Technology, 2014, 35(4): 470-478.)
[2] LIU Huo-xing, AN Yu-ge, ZOU Zheng-ping. Aerothermal Analysis of a Turbine with Rim Seal Cavity[R].ASME 2014-GT-25276.
[3] 周扬, 牛为民, 邹正平, 等. 轮毂封严气体对高压涡轮二次流动的影响[J]. 推进技术, 2006, 27(6): 515-520. (ZHOU Yang, NIU Wei-min, ZOU Zheng-ping, et al. Effects of Coolant Injection from Rim Seals on Secondary Flow in a High Pressure Turbine[J]. Journal of Propulsion Technology, 2006, 27(6): 515-520.)
[4] JIA Wei, LIU Huo-xing. Numerical Investigation of the Effects of Rim Seal on Turbine Aerodynamic Design Parameters and End Wall Flows in Low-Aspect Ratio Turbine[J]. Computer & Fluids, 2013, 74(5): 114-125.
[5] ZENG Jun, ZHANG Wei-tao. Numerical Simulation of the Interaction Between Rim Seal and Main Annulus Flow in a Four Sage Low-Pressure Axial Turbine[R]. AIAA 2015-3416.
[6] Montomoli F, Massini M, Maceli N, et al. Interaction of Wheelspace Coolant and Main Flow in a New Aeroderivative LPT[R]. ASME 2006-GT-90767.
[7] HU Jialin, DU Qiang, LIU Jun, et al. Flow Development Through HP & LP Turbines, Part II: Effects of the Hub Endwall Secondary Sealing Air Flow on the Turbine’s Mainstream Flow[J]. Journal of Thermal Science, 2017, 26(4): 308-315.
[8] Paniagua G, Deno R, Almeida S. Effect of the Hub Endwall Cavity Flow on the Flow-Field of a Transonic High-Pressure Turbine[J]. Journal of Turbomachinery, 2004, 126(4): 578-586.
[9] Turgut O H, Camci C. Computational Validation of the Flow Through a Turbine Stage and the Effects of Rim Seal Cavity Leakage on Secondary Flows[R]. ASME 2012-GT-69306.
[10] Schuepbach P, Abhari R S, Rose M G, et al. Influence of Rim Seal Purge Flow on the Performance of an Endwall-Profiled Axial Turbine[J]. Journal of Turbomachinery, 2011, 133(2).
[11] Blanco E D L R, Hodson H P, Vazquez R. Effect of the Leakage Flows and the Upstream Platform Geometry on the Endwall Flows of a Turbine Cascade[R]. ASME 2006-GT-90767.
[12] Popovi? I, Hodson H P. The Effects of Parametric Variation of Rim Seal Geometry on the Interaction Between Hub Leakage and Mainstream Flows in HP Turbine[R]. ASME 2012-GT-68025.
[13] Chilla M, Hodson H, Newman D. Unsteady Interaction Between Annulus and Turbine Rim Seal Flows[R]. ASME 2012-GT-69089.
[14] JIA Wei, LIU Huo-xing. Numerical Investigation of the Interaction Between Upstream Purge Flow and Mainstream in a Highly-Loaded Turbine[R]. ASME 2014-GT-25276.
[15] Behr T. Control of Rotor Tip Leakage and Secondary Flow by Casing Air Injection in Unshrouded Axial Turbines[D]. Dresden: Dresden University of Technology, 2007.
[16] Schuepbach P, Abhari R S, Rose M G, et al. Sensitivity of Turbine Efficiency and Flow Structures to Varying Purge Flow[J]. Journal of Propulsion and Power, 2010, 26(1): 46-56.
[17] Schuepbach P. Influence of Rim Seal Purge Flow on Performance of an End Wall Profiled Axial Turbine[D]. Swiss: Swiss Federal Institute of Technology, 2009.　　　　　　　　　　　　　　收稿日期:2018-07-09；修订日期:2018-08-30。基金项目:国家自然科学基金(51876176；51576163)。通讯作者:杨帆,博士生,研究领域为叶轮机械内复杂流动。E-mail: 1415515954@qq.com(编辑:朱立影)