叶片表面粗糙度对压气机叶栅内三维角区分离及损失研究

推进技术 ›› 2019, Vol. 40 ›› Issue (3): 504-514.

叶片表面粗糙度对压气机叶栅内三维角区分离及损失研究

刘凯¹,楚武利^1,2,张皓光¹,陈向艺¹,李金鸽¹,李兰攀¹

西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072; 先进发动机协同创新中心，北京 100191,西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072,西北工业大学动力与能源学院，陕西西安 710072

发布日期:2021-08-15
基金资助:
国家自然科学基金(51576162)；国家自然科学基金重点项目(51536006)；西北工业大学研究生创新创意种子基金。

Effectiveness of Blade Surface Roughness on 3D Corner Separation and Loss in Compressor Cascade

School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China,School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China;Collaborative Innovation Center of Advanced Aero-Engine，Beijing 100191，China,School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China,School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China,School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China and School of Power and Energy，Northwestern Polytechnical University，Xi’an 710072，China

Published:2021-08-15

摘要/Abstract

摘要： 在实际使用过程中，压气机容易由于腐蚀磨损等原因导致叶片表面粗糙度增加，这将使得整级压气机的气动性能下降。与此同时，由轮毂横向流所诱发的角区分离也将造成巨大的流动损失。为了探究叶表粗糙度变化是否会促进角区分离的产生，以及粗糙度变化对压气机内损失类型的影响，借助CFX商用软件对低雷诺数扩压叶栅展开数值计算研究。同时，还引入Gamma模型来研究粗糙度变化对转捩的影响。研究发现，叶片表面粗糙度的增加将使得分离转捩和旁路转捩加强，但对逆转捩影响较小。此外，借助损失源分析方法，将叶栅内的损失分为前缘损失、叶型摩擦损失、二次流损失和尾迹损失。结果表明，在角区分离严重且表面等效砂砾粗糙度增加到50μm时，相比于光滑情况，其总损失增加了9.6%。借助拓扑分析，可以发现随粗糙度增加，前缘分离泡不断前移，扰乱前缘部分流动，由此导致的前缘损失随粗糙度变化最为明显。

关键词: 压气机叶栅；粗糙度；损失；角区分离；拓扑分析

Abstract: The compressor blade surface roughness is easily deteriorated by deposits of ash and sand， as well as corrosion at wet environment， which results in the failure of aerodynamic behavior for compressor failed. Meanwhile， the three-dimensional (3D) separation near the hub causes large performance loss for compressor. Thus， a low-Reynolds compressor cascade was studied to investigate that whether the roughness on the blade can promote the 3D separation and make a difference on all type of the loss in the cascade or not by CFX. In this study， the Gamma transition model was introduced to investigate the influence of blade surface roughness to transition phenomenon. It can be concluded that the blade surface roughness has more effect on the separation transition and the bypass transition than the reverse transition. Furthermore， a detailed loss sources analysis model was used to study the loss influenced by the surface roughness， which divided the total loss in the cascade into the leading edge loss， the surface friction loss， the secondary flow loss and the wake flow loss. The results show that the total loss increases to 9.6% at large scale of corner separation condition when the equivalent sand grain roughness in the blades increases to 50μm. And the leading edge loss is most sensitive to the surface roughness. With the help of the topology analysis method， it can be found that the movement of the separation bubble is the most obvious phenomenon in the field as the roughness increasing.

Key words: Compressor cascade；Roughness；Loss；Corner separation；Topology analysis

刘凯,楚武利,张皓光,陈向艺,李金鸽,李兰攀. 叶片表面粗糙度对压气机叶栅内三维角区分离及损失研究[J]. 推进技术, 2019, 40(3): 504-514.

LIU Kai¹,CHU Wu-li^1,2,ZHANG Hao-guang¹,CHEN Xiang-yi¹,LI Jin-ge¹,LI Lan-pan¹. Effectiveness of Blade Surface Roughness on 3D Corner Separation and Loss in Compressor Cascade[J]. Journal of Propulsion Technology, 2019, 40(3): 504-514.

参考文献

[1] Hamed A A. Turbine Blade Surface Deterioration by Erosion[J]. Journal of Turbomachinery, 2005, 127(3):445-452.
[2] Bammert K, Woelk G U. The Influence of the Blading Surface Roughness on the Aerodynamic Behavior and Characteristic of an Axial Compressor[J]. Journal of Engineering for Gas Turbines & Power, 1980, 102(2).
[3] Chen S, Zhang C, Shi H, et al. Study on the Impact of Fouling on Axial Compressor Stage[R]. ASME 2012-GT-68041.
[4] Doering Felix, Staudacher S, Koch C, et al. Modeling Particle Deposition Effects in Aircraft Engine Compressors[J]. Journal of Turbomachinery, 2017, 139(5).
[5] Asme T, Melino F, Morini M, et al. Compressor Fouling Modeling: Relationship Between Computational Roughness and Gas Turbine Operation Time[J]. Journal of Engineering for Gas Turbines & Power, 2011, 134(5): 1011-1019.
[6] Back S C, Jeong I C, Sohn J L, et al. Influence of Surface Roughness on the Performance of a Compressor Blade in a Linear Cascade: Experiment and Modeling[R]. ASME 2009-GT-59703.
[7] Goodhand M N, Walton K, Blunt L, et al. The Limitations of “Ra” to Describe Surface Roughness[R]. ASME 2015-GT-43329.
[8] Hergt A, Meyer R, Engel K. Experimental Investigation of Flow Control in Compressor Cascades[R]. ASME 2006-GT-90415.
[9] Zhiyuan Li, Du J, Jemcov A, et al. A Study of Loss Mechanism in a Linear Compressor Cascade at the Corner Stall Condition[R]. ASME 2017-GT-65192.
[10] 罗华玲, 乔渭阳, 许开富, 等. 自由流湍流度对某低压涡轮级气动影响的数值研究[J]. 航空动力学报, 2008, 23(8): 1490-1497.
[11] 张燕峰. 高载荷压气机端壁流动及其控制策略研究[D]. 西安:西北工业大学, 2010.
[12] Lei V M, Spakovszky Z S, Greitzer E M. A Criterion for Axial Compressor Hub-Corner Stall[R]. ASME 2006-GT-91332.
[13] Heydorn A, S?ndergaard B P, Ersb?ll B, et al. Effects of Vortex Generator Application on the Performance of a Compressor Cascade[J]. Journal of Turbomachinery, 2010, 132(2).
[14] Chen P P, Qiao W Y, Liesner K, et al. Effect of Segment Endwall Boundary Layer Suction on Compressor 3D Corner Separation[R]. ASME 2015-GT-42024.
[15] Chu W, Li X, Wu Y, et al. Reduction of End Wall Loss in Axial Compressor by Using Non-Axisymmetric Profiled End Wall: A New Design Approach Based on End Wall Velocity Modification[J]. Aerospace Science & Technology, 2016, (55): 76-91.
[16] 田思濛, 吴云, 张海灯, 等. 基于能量耗散率的低速扩压叶栅损失研究[J]. 航空学报, 2015, 36(10):3249-3262.
[17] Aldi N, Morini M, Pinelli M, et al. Performance Evaluation of Non-Uniformly Fouled Axial Compressor Stages by Means of Computational Fluid Dynamic Analyses[J]. Journal of Turbomachinery, 2014, 136(2).
[18] Hunt J C R, Wray A A, Moin P. Eddies, Streams, and Convergence Zones in Turbulent Flows[J]. Studying Turbulence Using Numerical Simulation Databases, 1988, (2): 193-208.
[19] 童秉纲, 尹协远, 朱克勤. 涡运动理论-第2版[M]. 合肥:中国科学技术大学出版社, 2009.　　　　　　　　　　　　　　收稿日期:2018-01-23；修订日期:2018-05-04。基金项目:国家自然科学基金(51576162)；国家自然科学基金重点项目(51536006)；西北工业大学研究生创新创意种子基金。通讯作者:刘凯,硕士生,研究领域为叶轮机气动热力学。E-mail: louis_kai@qq.com(编辑:梅瑛)