薄壁机匣螺栓连接结构多目标优化设计

推进技术 ›› 2019, Vol. 40 ›› Issue (4): 876-883.

薄壁机匣螺栓连接结构多目标优化设计

沈阳航空航天大学辽宁省航空推进系统先进测试技术重点实验室，辽宁沈阳110136,沈阳航空航天大学辽宁省航空推进系统先进测试技术重点实验室，辽宁沈阳110136,沈阳航空航天大学辽宁省航空推进系统先进测试技术重点实验室，辽宁沈阳110136,沈阳航空航天大学辽宁省航空推进系统先进测试技术重点实验室，辽宁沈阳110136,沈阳航空航天大学辽宁省航空推进系统先进测试技术重点实验室，辽宁沈阳110136

发布日期:2021-08-15
作者简介:艾延廷，博士，教授，研究领域为航空发动机强度、振动及噪声。E-mail: ytai@163.com 通讯作者:田晶，博士生，工程师，研究领域为航空发动机强度、振动及可靠性。
基金资助:
国家自然科学基金(11702177)；辽宁省教育厅项目(LN201710)。

关键词:薄壁机匣；振动强度分析；响应面模型；多目标优化

Liaoning Key Laboratory of Advanced Measurement and Test Technology for Aviation Propulsion System，Shenyang Aerospace University，Shenyang 110136，China,Liaoning Key Laboratory of Advanced Measurement and Test Technology for Aviation Propulsion System，Shenyang Aerospace University，Shenyang 110136，China,Liaoning Key Laboratory of Advanced Measurement and Test Technology for Aviation Propulsion System，Shenyang Aerospace University，Shenyang 110136，China,Liaoning Key Laboratory of Advanced Measurement and Test Technology for Aviation Propulsion System，Shenyang Aerospace University，Shenyang 110136，China and Liaoning Key Laboratory of Advanced Measurement and Test Technology for Aviation Propulsion System，Shenyang Aerospace University，Shenyang 110136，China

Published:2021-08-15

摘要/Abstract

摘要： 为增大薄壁机匣安装边螺栓连接结构强度、减小其振动和重量，以满足现代航空发动机更高性能的要求，对机匣结构参数进行了优化设计。选取安装边高度、安装边厚度、机匣厚度和螺栓个数为参数变量，结构质量、一阶固有频率和最大等效应力为目标函数，根据Box-Behnken方法设计的样本点和有限元计算结果建立二阶响应面模型，基于层次分析获取权系数，并利用遗传算法对机匣结构进行多目标优化设计。最后，针对优化后的结构进行模态试验和有限元验证。研究表明，模态试验结果与有限元计算误差小于6%，同时优化显著提高了一阶固有频率，使其结构质量和最大等效应力分别降低5.28%和13.64%，验证了本文提出的优化方法的有效性和可行性。

关键词: 薄壁机匣；振动强度分析；响应面模型；多目标优化

Abstract: In order to increase the strength of bolt connected flange for thin-walled casing and reduce thestructural vibration and weight，and satisfy the higher performance of advanced aero-engines，the optimization design was studied for the structural parameters of casing model. The height and thickness of the flange，casing thickness and bolt numbers were selected as parameters variables. The structural mass，first natural frequency and maximum equivalent stress were determined as objective functions. The second-order response surface model was established according to the sample points by Box-Behnken method and the finite element calculation results.The weight coefficients were obtained by Analytic Hierarchy Process，and the genetic algorithm was adopted to conduct the multi-objective optimization of the casing. Finally，the modal tests and the finite element verification were performed on the optimized structure. The research indicates that the error between the modal test results and the finite element calculation is less than 6%. Meanwhile，the optimization has greatly increased the first natural frequency and reduced the structural mass and maximum equivalent stress by 5.28% and 13.64% respectively，which verifies the effectiveness and the feasibility of the optimization method proposed in this paper.

Key words: Thin-walled casing；Vibration strength analysis；Response surface model；Multi-objective

AI Yan-ting,LIU Hai-yue,TIAN Jing,ZHOU Jie,WANG Zhi. 薄壁机匣螺栓连接结构多目标优化设计[J]. 推进技术, 2019, 40(4): 876-883.

AI Yan-ting,LIU Hai-yue,TIAN Jing,ZHOU Jie,WANG Zhi. 关键词:薄壁机匣；振动强度分析；响应面模型；多目标优化[J]. Journal of Propulsion Technology, 2019, 40(4): 876-883.

参考文献

[1] 王海涛.带预紧力螺栓连接的机匣刚度分析[J].航空发动机,2010,36(3): 33-35.
[2] Kim M,Kim Y,Kim P,et al.Design Optimization of Double-Array Bolted Joints in Cylindrical Composite Structures[J].International Journal of Aeronautical & Space Sciences,2016,17(3): 332-340.Fig.8 Vibration shape comparison of finite element calculation and modal test
[3] 《航空发动机设计手册》总编委会.载荷及机匣承力件强度分析(第17 册)[M].北京:航空工业出版社,2001.
[4] 蔡显新,肖新红,王涛,等.风扇机匣的减振优化设计[J].航空动力学报,2010,25(2): 396-401.
[5] 张春宜,刘令君,孙旭东,等.基于双重响应面法的航空发动机叶片振动概率分析[J].推进技术,2017,38(4): 918-924.(ZHANG Chun-yin,LIU Ling-jun,SUN Xu-dong,et al.Vibration Probability Analysis of Aero-Engine Blades Based on Double Response Surface Method[J].Journal of Propulsion Technology,2017,38(4): 918-924.)
[6] 戴雄,关玉璞,赵振华,等.高压涡轮机匣热固耦合下多目标优化方法[J].航空动力学报,2017,32(8): 1992-1999.
[7] Panda S,Yegireddy N K.Automatic Generation Control of Multi-Area Power System Using Multi-ObjectiveNon-Dominated Sorting Genetic Algorithm-II[J].Inter?national Journal of Electrical Power & Energy Systems,2013,53(4): 54-63.
[8] 向纪鑫,孙冰,徐华.基于响应面法的再生冷却通道尺寸传热优化[J].推进技术,2017,38(11):2580-2587.(XIANG Ji - xin,SUN Bing,XU Hua.Thermal Optimization for Regenerative-Cooled ChannelDimension Based on Response Surface Methodology[J].Journal of Propulsion Technology,2017,38(11): 2580-2587.)
[9] Abid M,Khan A,Nash D H,et al.Optimized Bolt Tightening Strategies for Gasketed Flanged Pipe Joints of Different Sizes[J].International Journal of Pressure Ves?sels & Piping,2016,139: 22-27.
[10] Lee D H,Hwang W S.An Indentification Method Joint Structural Parameters Using an FRF Based Sub-Structuring Method and an Optimization Technique[J].Jour?nal of Mechanical Science and Technology,2007,(21):2011-2022.
[11] Zare S,Tavakolpour-Saleh A R.Frequency-Based Design of a Free Piston Stirling Engine Using Genetic Algorithm[J].Energy,2016,109: 466-480.
[12] 代汉超,石雪飞,阮欣.基于改进响应面的桥梁抗弯刚度修正[J].中南大学学报(自然科学版),2014,45(7): 2387-2393.
[13] Hou S,Li Q,Long S,et al.Multiobjective Optimization of Multi-Cell Sections for the Crashworthiness Design[J].International Journal of Impact Engineering,2008,35(11): 1355-1367.
[14] Wang H,Zong C,Guan X,et al.Method of Determining Weights of Subjective Evaluation Indexes for Car Handling and Stability Based on Fuzzy Analytic Hierarchy Process[J].Journal of Mechanical Engineering,2011,47(24): 83-90.
[15] Schwingshackl C W,Maio D D,Sever I,et al.Modeling and Validation of the Nonlinear Dynamic Behavior of Bolted Flange Joints[J].Journal of Engineering for Gas Turbines & Power,2013,135(12): 385-399.
[16] 艾延廷,路闯,武威,等.机匣横向安装边螺栓联接结构应力分析[J].航空制造技术,2015,472(3): 25-29.
[17] 温登哲,陈予恕.径向简谐激励下航空发动机机匣的振动分析[J].航空动力学报,2015,30(1): 96-105.(编辑:陈夏夏)* 收稿日期:2018-05-14；修订日期:2018-07-05。基金项目:国家自然科学基金(11702177)；辽宁省教育厅项目(LN201710)。作者简介:艾延廷,博士,教授,研究领域为航空发动机强度、振动及噪声。E-mail: ytai@163.com通讯作者:田晶,博士生,工程师,研究领域为航空发动机强度、振动及可靠性。E-mail: tianjing@188.com