端壁转动对凹槽叶尖流动换热性能的影响

推进技术 ›› 2019, Vol. 40 ›› Issue (5): 1005-1014.

端壁转动对凹槽叶尖流动换热性能的影响

皮骏¹,杜旭博²,孔庆国³,刘光才¹

中国民航大学通用航空学院，天津 300300,中国民航大学航空工程学院，天津 300300,中国民航大学中欧航空工程师学院，天津 300300,中国民航大学通用航空学院，天津 300300

发布日期:2021-08-15
作者简介:皮骏，博士，副教授，研究领域为叶轮机械转子振动分析与故障诊断。E-mail:jpi@cauc.edu.cn 通讯作者:杜旭博，硕士生，研究领域为叶轮机械气动传热。
基金资助:
国家自然科学基金委员会与中国民用航空局联合资助(U1633101)；中央高校基本科研业务费民航大学专项

Effects of End-Wall Rotation on Aerothermal Performance of Squealer Tip

College of General Aviation，Civil Aviation University of China，Tianjin 300300，China,School of Aeronautical Engineering，Civil Aviation University of China，Tianjin 300300，China,Sino-European Institute of Aviation Engineering，Civil Aviation University of China，Tianjin 300300，China and College of General Aviation，Civil Aviation University of China，Tianjin 300300，China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究端壁转动对跨声速凹槽叶尖流动换热性能的影响，采用数值方法，详细研究了三种冷却孔结构凹槽叶尖在端壁转动条件下的叶尖间隙流场、冷却流流态、气膜冷却效率、叶尖表面换热系数和叶尖泄漏流量，同时考虑凹槽深度和端壁转动速度的影响。结果表明:端壁转动在叶尖凹槽内形成与泄漏流分离涡方向相反的旋涡，使泄漏流在凹槽底面的再附增强，在凹槽突肩的再附减弱。端壁转动能减少叶尖泄漏流量，研究范围内，叶尖相对泄漏流量最多减小20%。随着凹槽深度增大，叶尖平均气膜冷却效率随之增大，叶尖平均换热系数和叶尖泄漏流量随之减小。随着端壁转速减小，叶尖泄漏流量随之增大，压力侧和吸力侧冷却孔模型的叶尖平均气膜冷却效率随之减小，而中弧线冷却孔模型的叶尖平均气膜冷却效率随之增大。压力侧喷入冷却气流，叶尖的气膜冷却效果最好。

关键词: 高压涡轮；叶尖凹槽；端壁转动；换热系数；叶尖泄漏流

Abstract: In order to investigate the effects of end-wall rotation on aerothermal performance of transonic squealer tip， the flow field， cooling injection behavior， cooling effectiveness， tip heat transfer and over tip leakage flow rate of the squealer tip with three different cooling configurations under end-wall rotation were in detail studied use a numerical method. The effects of squealer depth and rotation velocity were also considered. The results show that the end-wall rotation forms a vortex opposite to the direction of the leakage flow separate vortex within the tip squealer， the reattachment of leakage flow on the squealer floor increases， and the reattachment of leakage flow is decreased at the squealer rim inversely. The rotation of the end-wall can reduce the over tip leakage flow， and the maximum decrease is up to 20% at the research range relatively. With the increase of squealer depth， the average film cooling efficiency of squealer tip increases， the average heat transfer coefficient and the over tip leakage flow ratio of the blade tip decreases accordingly. With the decrease of the rotation speed， the over tip leakage flow ratio increases， the average film cooling efficiency of squealer tip on pressure side and the suction side cooling model decreases， the average film cooling efficiency of squealer tip on camber line cooling model increases inversely. Pressure side film cooing model have the best cooling effectiveness on squealer tip.

Key words: High pressure turbine；Tip squealer；End-wall rotation；Heat transfer coefficient；Over tip leakage flow

皮骏,杜旭博,孔庆国,刘光才. 端壁转动对凹槽叶尖流动换热性能的影响[J]. 推进技术, 2019, 40(5): 1005-1014.

PI Jun¹,DU Xu-bO²,KONG Qing-guo³,LIU Guang-cai¹. Effects of End-Wall Rotation on Aerothermal Performance of Squealer Tip[J]. Journal of Propulsion Technology, 2019, 40(5): 1005-1014.

参考文献

[1] Kwak Jae Su, Han Je-Chin.Heat Transfer Coefficients on the Squealer Tip and near Squealer Tip Regions of a Gas Turbine Blade[J]. Journal of Heat Transfer, 2002, 125(4): 778-787.
[2] Nasir H, Ekkad S V, Kontrovitz D M. Effect of Tip Gap and Squealer Geometry on Detailed Heat Transfer Measurements over a High Pressure Turbine Rotor Blade Tip[J]. Journal of Turbomachinery, 2004, 126(2):221-228.
[3] Wang J, Sundén B, Zeng M, et al. Influence of Different Rim Widths and Blowing Ratios on Film Cooling Characteristics for a Blade Tip[J]. Journal of Heat Transfer, 2012, 134(6).
[4] Zhou C, Hodson H. Squealer Geometry Effects on Aerothermal Performance of Tip-Leakage Flow of Cavity Tips[J]. Journal of Propulsion and Power, 2012, 28(3):556-567.
[5] 王大磊, 朴英. 间隙高度对某涡轮叶尖间隙泄漏流影响的研究[J]. 推进技术, 2012, 33(4):566-572. (WANG Da- lei, PIAO Ying. Influence of Tip Clearance Size on Tip Clearance Flow of a Transonic Turbine[J]. Journal of Propulsion Technology, 2012, 33(4):566-572.)
[6] Nho Y C, Yong J L, Kwak J S. Effects of Tip Shape on the Gas Turbine Blade Tip Heat Transfer[J]. Journal of Thermophysics and Heat Transfer, 2015, 26(2):305-312.
[7] Zhong F, Zhou C, Ma H, et al. Heat Transfer of Winglet Tips in a Transonic Turbine Cascade[J]. Journal of Engineering for Gas Turbines and Power, 2016, 139(1).
[8] Christophel J R, Couch E, Thole K A, et al. Measured Adiabatic Effectiveness and Heat Transfer for Blowing from the Tip of a Turbine Blade[J]. Journal of Turbomachinery, 2005, 127(2): 251-262.
[9] Wang Z, Zhang Q, Liu Y, et al. Impact of Cooling Injection on the Transonic Over-Tip Leakage Flow and Squealer Aerothermal Design Optimization[J]. Journal of Engineering for Gas Turbines and Power, 2015, 137(6).
[10] Ma H, Zhang Q, He L, et al. Cooling Injection Effect on a Transonic Squealer Tip, Part I: Experimental Heat Transfer Results and CFD Validation[J]. Journal of Engineering for Gas Turbines and Power, 2017, 139(5).
[11] Ma H, Zhang Q, He L, et al. Cooling Injection Effect on a Transonic Squealer Tip, Part II: Analysis of Aerothermal Interaction Physics[J]. Journal of Engineering for Gas Turbines and Power, 2017, 139(5).
[12] Yang D, Yu X, Feng Z. Investigation of Leakage Flow and Heat Transfer in a Gas Turbine Blade Tip with Emphasis on the Effect of Rotation[J]. Journal of Turbomachinery, 2010, 132(4).
[13] Acharya S, Moreaux L. Numerical Study of the Flow Past a Turbine Blade Tip: Effect of Relative Motion Between Blade and Shroud[J]. Journal of Turbomachinery, 2012, 136(3): 471-480.
[14] Palafox P P, Oldfield M G, Ireland P T, et al. Blade Tip Heat Transfer and Aerodynamics in a Large Scale Turbine Cascade with Moving Endwall[J]. Journal of Turbomachinery, 2011, 134(2).
[15] 杜昆, 宋立明, 李军. 凹槽状叶顶涡轮叶片传热特性的数值研究[J]. 推进技术, 2014, 35(5): 618-623. (DU Kun, SONG Li-ming, LI Jun. Numerical Investigations on Heat Transfer Characteristics of Turbine Blade with Squealer Tip[J]. Journal of Propulsion Technology, 2014, 35(5): 618-623.)
[16] Zhou C. Aerothermal Performance of Different Tips in Transonic Turbine Cascade with End-Wall Motion[J]. Journal of Propulsion and Power, 2014, 30(5): 1-12.
[17] Rezasoltani M, Lu K, Schobeiri M T, et al. A Combined Experimental and Numerical Study of the Turbine Blade Tip Film Cooling Effectiveness under Rotation Condition[J]. Journal of Turbomachinery, 2015, 137(5).
[18] Cortelezzi L, Karagozian A R. On the Formation of the Counter-Rotating Vortex Pair in Transverse Jets[J]. Journal of Fluid Mechanics, 2001, 446(1): 347-373.(编辑:朱立影)　　　　　　　　　　　　　　收稿日期:2018-03-23；修订日期:2018-06-20。基金项目:国家自然科学基金委员会与中国民用航空局联合资助(U1633101)；中央高校基本科研业务费民航大学专项基金(3122013H001)。作者简介:皮骏,博士,副教授,研究领域为叶轮机械转子振动分析与故障诊断。E-mail:jpi@cauc.edu.cn通讯作者:杜旭博,硕士生,研究领域为叶轮机械气动传热。E-mail: xubo_du@163.com