存在剥离条件下颗粒物沉积过程的数值研究和实验验证

doi:10.13675/j.cnki. tjjs. 180488

推进技术 ›› 2019, Vol. 40 ›› Issue (7): 1523-1535.DOI: 10.13675/j.cnki. tjjs. 180488

存在剥离条件下颗粒物沉积过程的数值研究和实验验证

1.中国民航大学航空工程学院，天津 300300;2.中国民航大学中欧航空工程师学院，天津;300300

发布日期:2021-08-15
基金资助:
国家自然科学基金委员会与中国民用航空局联合资助项目 U1633113国家自然科学基金委员会与中国民用航空局联合资助项目（U1633113）。

Experimental Validation and Numerical Simulation ofParticles Depositional Processes with Detachment

1.School of Aeronautical Engineering,Civil Aviation University of China,Tianjin 300300,China;2.Sino-European Institute of Aviation Engineering,Civil Aviation University of China,Tianjin 300300,China

Published:2021-08-15

摘要/Abstract

摘要： 为了更加准确地模拟涡轮叶片表面颗粒物沉积的增长过程和分布状况，研究颗粒物沉积过程中粘附、剥离直至稳定平衡的规律，在经改进的颗粒粘附模型基础上考虑两种剥离形式，利用Fluent的User Defined Function (UDF)功能和网格重构技术，最终实现了熔融石蜡颗粒于带有气膜冷却的平板上沉积动态增长的过程。通过与相同条件下所得实验结果的对比，验证了所用模型的有效性和合理性。随后研究了是否加入剥离模型、气膜冷却吹风比、气膜孔射流角度等因素对沉积效果的影响。计算结果表明，考虑颗粒的剥离效应将减少颗粒物沉积的总量，尤其是在气膜孔后较短区域内；此外，吹风比的增加将使颗粒不易撞击壁面，已粘附的颗粒也更容易剥离从而降低沉积的厚度和质量；射流角度不断增大则使气膜覆盖效果变差，壁面温度升高，颗粒更易达到熔融状态沉积下来。研究发现该数值方法有助于更加精确地仿真沉积增长的过程，证实了吹风比和射流角度对沉积的分布和厚度有很大影响。当射流角度处于35°~40°时，可在一定程度上减少沉积。

关键词: 涡轮;叶片;沉积过程;剥离模型;颗粒;气膜冷却

Abstract: In order to simulate the growth process and distribution of particles deposition on the surface of turbine blades more accurately and study the rules of sticking, detachment and developing stably during the process of particles deposition, the User Defined Function (UDF) in FLUENT and mesh reconstruction technology was used to perform the dynamic growth of molten wax particles deposition on the surface of plate with film cooling, which was based on a new particle sticking model and two kinds of detachment methods. The validity and rationality of the model were guaranteed by comparison with the experimental results obtained under the same conditions. Subsequently, the effects of the detachment model, the blow ratios, and the jet angle of film holes were investigated in detail. The calculation results show that considering the detachment of the particles reduces the total amount of particulate deposits, especially in the area behind of the film holes. In addition, the increase of the blowing ratio makes the particles less likely to impact on the wall surface, and the adhered particles are also more easily peeled off, thus reducing the thickness and mass of the deposition. What’s more, the increasing jet angle not only reduces the cooling effectiveness of the film holes, but increases the wall surface temperature, and the particles are more easily deposited in molten state. It is found that this study is helpful to simulate the process of deposition growth more accurately, and it is proved that the blowing ratio and jet angle have great influence on the deposition distribution and thickness. When the jet angle is between 35°~40°, it may reduce deposition to some extent.

Key words: Turbine;Blade;Depositional processes;Detachment model;Particles;Film cooling

. 存在剥离条件下颗粒物沉积过程的数值研究和实验验证[J]. 推进技术, 2019, 40(7): 1523-1535.

参考文献

[1] Hamed A, Tabakoff W C, Wenglarz R V. Erosion and Deposition in Turbomachinery[J]. Journal of Propulsion and Power, 2006, 22(2): 350-360.
[2] Bogard D G, Schmidt D L, Tabbita M. Characterization and Laboratory Simulation of Turbine Airfoil Surface Roughness and Associated Heat Transfer[R]. ASME 96-GT-386.
[3] Dunn M G. Operation of Gas Turbine Engines in an Environment Contaminated with Volcanic Ash[J]. Journal of Turbomachinery, 2012, 134(5).
[4] Dunn M G, Padova C, Moller J E, et al. Performance Deterioration of a Turbofan and a Turbojet Engine upon Exposure to a Dust Environment[J]. Journal of Engineering for Gas Turbines and Power, 1987, 109(3): 336-343.
[5] Kim J, Dunn M G, Baran A J, et al. Deposition of Volcanic Materials in the Hot Sections of Two Gas Turbine Engines[R]. ASME 92-GT-219.
[6] Jensen J W, Squire S W, Bons J P, et al. Simulated Land-Based Turbine Deposits Generated in an Accelerated Deposition Facility[J]. Journal of Turbomachinery, 2005, 127(3):462-470.
[7] Bons J P, Wammack J E, Crosby J, et al. Evolution of Surface Deposits on a High-Pressure Turbine Blade—Part II: Convective Heat Transfer[J]. Journal of Turbomachinery, 2008, 130(2).
[8] Crosby J M, Lewis S, Bons J P, et al. Effects of Particle Size, Gas Temperature and Metal Temperature on High Pressure Turbine Deposition in Land Based Gas Turbines from Various Synfuels[R]. ASME GT2007-27531.
[9] Lewis S, Barker B, Bons J P, et al. Film Cooling Effectiveness and Heat Transfer near Deposit-Laden Film Holes[J]. Journal of Turbomachinery, 2011, 133(3).
[10] Lawson S A, Thole K A. The Effects of Simulated Particle Deposition on Film Cooling[R]. ASME GT2009-59109.
[11] Mensch A, Thole K. Simulations of Multiphase Particle Deposition on a Gas Turbine Endwall with Impingement and Film Cooling[J]. Journal of Turbomachinery, 2015, 137(11).
[12] Tabakoff W, Hamed A, Metwally M. Effect of Particle Size Distribution on Particle Dynamics and Blade Erosion in Axial Flow Turbines[J]. Journal of Engineering for Gas Turbines & Power, 1990, 112(4):607-615.
[13] Brach R M, Dunn P F. A Mathematical Model of the Impact and Adhesion of Microsphers[J]. Aerosol Science and Technology, 1992, 16(1): 51-64.
[14] El-Batsh H, Haselbacher H. Numerical Investigation of the Effect of Ash Particle Deposition on the Flow Field through Turbine Cascades[R]. ASME GT2002-30600.
[15] Sreedharan S S, Tafti D K. Composition Dependent Model for the Prediction of Syngas Ash Deposition with Application to a Leading Edge Turbine Vane[R]. ASME GT2010-23655.
[16] Barker B, Casaday B, Shankara P, et al. Coal Ash Deposition on Nozzle Guide Vanes—Part II: Computational Modeling[J]. Journal of Turbomachinery, 2013, 135(1).
[17] Casari N, Pinelli M, Suman A, et al. EBFOG: Deposition, Erosion, and Detachment on High-Pressure Turbine Vanes[J]. Journal of Turbomachinery, 2018, 140(6).
[18] Bons J P, Prenter R, Whitaker S A. Simple Physics-Based Model for Particle Rebound and Deposition in Turbomachinery[J]. Journal of Turbomachinery, 2017, 139(8).
[19] 周君辉, 张靖周. 涡轮叶栅内粒子沉积特性的数值研究[J]. 航空学报，2013，34(11):2492-2499.
[20] 周君辉,张靖周. 气膜孔附近粒子沉积特性的数值研究[J].航空动力学报,2014, 29（9）: 2166-2173.
[21] 裴钰. 燃气轮机涡轮叶片表面污染物沉积模型研究[D]. 天津:中国民航大学, 2016.
[22] 杨晓军, 祝佳雄. 涡轮叶栅通道内颗粒物沉积过程的数值模拟[J]. 航空学报, 2017, 38(5):31-42.
[23] 杨晓军, 崔莫含, 刘智刚. 气膜冷却平板表面颗粒物沉积的实验研究[J]. 推进技术, 2018, 39(6): 1323-1330. （YANG Xiao-jun, CUI Mo-han, LIU Zhi-gang. Experimental Study on Particle Deposition of Plate Surface with Film Cooling[J]. Journal of Propulsion Technology, 2018, 39(6): 1323-1330.）
[24] Elghobashi S. On Predicting Particle-Laden Turbulent Flows[J]. Applied Scientific Research, 1994, 52(4): 309-329.
[25] Song W, Yan L, Hess K U, et al. Volcanic Ash Melting under Conditions Relevant to Ash Turbine Interactions[J]. Nature Communications, 2016, 7： 10795.
[26] Senior C L, Srinivasachar S. Viscosity of Ash Particles in Combustion Systems for Prediction of Particle Sticking[J]. Energy & Fuels, 1995, 9(2): 277-283.
[27] Soltani M, Ahmadi G. On Particle Adhesion and Removal Mechanisms in Turbulent Flows[J]. Journal of Adhesion Science and Technology, 1994, 8(7): 763-785.
[28] El-Batsh M S H. Modeling Particle Deposition on Compressor and Turbine Blade Surfaces[D]. Vienna: Vienna University of Technology, 2001.
[29] Lawson S A, Thole K A. Simulations of Multiphase Particle Deposition on Endwall Film-Cooling[J]. Journal of Turbomachinery, 2012, 134(1).
[30] Bonilla C, Webb J, Clum C, et al. The Effect of Particle Size and Film Cooling on Nozzle Guide Vane Deposition[J]. Journal of Engineering for Gas Turbines and Power, 2012, 134(10).

存在剥离条件下颗粒物沉积过程的数值研究和实验验证

Experimental Validation and Numerical Simulation ofParticles Depositional Processes with Detachment

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价