气膜孔倾角角度对单晶高温合金疲劳性能的影响

doi:10.13675/j.cnki.tjjs.200198

推进技术 ›› 2021, Vol. 42 ›› Issue (1): 192-199.DOI: 10.13675/j.cnki.tjjs.200198

气膜孔倾角角度对单晶高温合金疲劳性能的影响

张冬旭¹，何金洋¹，温志勋²，刘路²，梁建伟¹

1.陕西科技大学机电工程学院，陕西西安 710021;2.西北工业大学力学与土木建筑学院，陕西西安 710129

出版日期:2021-01-15 发布日期:2021-01-15
基金资助:
国家自然科学基金（51805307）；陕西省自然科学基础研究计划（2020JQ-694）。

Effects of Slant Angle of Film Hole on Fatigue Properties of Single Crystal Superalloy

1.College of Mechanical and Electrical Engineering，Shaanxi University of Science and Technology，Xi’an 710021，China;2.School of Mechanics，Civil Engineering and Architecture，Northwestern Polytechnical University， Xi’an 710129，China

Online:2021-01-15 Published:2021-01-15

摘要/Abstract

摘要： 为了研究气膜孔倾角角度对单晶高温合金疲劳性能的影响，设计倾角30°，45°，90°的14孔平板试样进行了同等应力水平下的高温疲劳试验，并对断裂后失效试件进行断口分析。基于晶体塑性理论，对不同倾角气膜孔平板件进行数值计算，分析孔边局部应力及损伤演化。结果表明，气膜孔倾角角度对疲劳性能影响显著，疲劳寿命90°>30°>45°，且45°倾角气膜孔孔边裂纹数明显多于其他两种。数值模拟显示，90°孔每个循环累积的应变相对较小，30°斜孔次之，45°斜孔最大，且 45°斜孔和 30°斜孔的棘轮应变累积速率明显高于直孔，30°斜孔的损伤和直孔的损伤较为接近，45°斜孔的损伤最大，数值分析与实验结果相一致。

关键词: 气膜孔;倾角角度;疲劳寿命;晶体塑性理论;单晶高温合金

Abstract: In order to study the effects of the slant angle of film hole on the fatigue properties of single crystal superalloy， high temperature fatigue tests were carried out on 14 hole flat specimens with designed angle of 30°， 45?， 90?，respectively， under the same stress level， and the fracture analysis was carried out on the failure specimens. Based on the theory of crystal plasticity， numerical calculation was carried out for the flat plate with different slant angles of film holes， and the local stress and damage evolution of the hole edge were analyzed. The results show that the slant angle of the holes has a significant effect on the fatigue performance， and the order of the fatigue life is 90°>30°>45°. The number of cracks on the holes with the slant angle of 45° is significantly more than the other two type specimens. The numerical simulation shows that the accumulated strain of each cycle of 90° hole is relatively small， followed by 30° slant angle specimen and 45° slant angle specimen. The ratchet strain accumulation rates of 45° slant angle specimen and 30° slant angle specimen，respectively， are significantly higher than that of straight hole. The damage of 30° slant angle specimen is close to that of straight hole， and the damage of 45° skew hole is the largest. The calculation results are consistent with the experimental results.

Key words: Film hole;Slant angle;Fatigue life;Crystal plasticity theory;Single crystal superalloy

张冬旭，何金洋，温志勋，刘路，梁建伟. 气膜孔倾角角度对单晶高温合金疲劳性能的影响[J]. 推进技术, 2021, 42(1): 192-199.

ZHANG Dong-xu¹, HE Jin-yang¹, WEN Zhi-xun², LIU Lu², LIANG Jian-wei¹. Effects of Slant Angle of Film Hole on Fatigue Properties of Single Crystal Superalloy[J]. Journal of Propulsion Technology, 2021, 42(1): 192-199.

参考文献

[1] 邹望之，郑新前. 航空涡轴发动机发展趋势［J］. 航空动力学报， 2019（12）： 2577-2588.
[2] 刘大响. 一代新材料，一代新型发动机：航空发动机的发展趋势及其对材料的需求［J］. 材料工程， 2017， 45（10）： 1-5.
[3] 曹建国. 航空发动机仿真技术研究现状、挑战和展望［J］. 推进技术， 2018， 39（5）： 961-970.
[4] 梁春华，索德军，孙明霞. 美国第6代战斗机发动机关键技术综述［J］. 航空发动机， 2016， 42（2）： 93-97.
[5] 周明，杨青峰，张洪玉. 航空涡轮叶片气膜冷却孔激光加工技术进展［J］. 中国基础科学， 2016，（5）： 35-42.
[6] 刘维伟. 航空发动机叶片关键制造技术研究进展［J］. 航空制造技术， 2016， 59（21）： 50-56.
[7] 胡春燕，刘新灵，陶春虎. 电液束加工对DD6单晶合金气膜孔损伤行为研究［J］. 稀有金属材料与工程， 2019， 48（10）： 3190-3194.
[8] 刘新灵，陶春虎，刘春江，等. 航空发动机叶片气膜孔加工方法及其演变分析［J］. 材料导报， 2013，（21）： 120-123.
[9] Mazur Z， Luna-Ramírez A， Juárez-Islas J A， et al. Failure Analysis of a Gas Turbine Blade Made of Inconel 738LC Alloy［J］. Engineering Failure Analysis， 2005， 12（3）： 474-486.
[10] Lee K D， Kim K Y. Shape Optimization of a Fan-Shaped Hole to Enhance Film-Cooling Effectiveness［J］. International Journal of Heat & Mass Transfer， 2010， 53（15-16）： 2996-3005.
[11] Lu Y， Allison D， Ekkad S V. Turbine Blade Showerhead Film Cooling： Influence of Hole Angle and Shaping［J］. International Journal of Heat & Fluid Flow， 2007， 28（5）： 922-931.
[12] Liu C L， Zhu H R， Zhang Z W， et al. Experimental Investigation on the Leading Edge Film Cooling of Cylindrical and Laid-Back Holes with Different Hole Pitches［J］. International Journal of Heat & Mass Transfer， 2012， 55（23-24）： 6832-6845.
[13] Sun E， Heffernan T， Helmink R. Stress Rupture and Fatigue in Thin Wall Single Crystal Superalloys with Cooling Holes［J］. Superalloys， 2012， 53（12）： 351.
[14] Zhang Y M， Wen Z X， Pei H Q， et al. Equivalent Model of Close-Packed Film Cooling Holes in Nickel-Based Single Crystal Cooled Black Based on Crystallographic Theory［J］. Chinese Journal of Aeronautics， 2019， 32（4）： 839-850.
[15] Wen Z X， Pei H Q， Yang H， et al. A Combined CP Theory and TCD for Predicting Fatigue Lifetime in Single-Crystal Superalloy Plates with Film Cooling Holes［J］. International Journal of Fatigue， 2018， 111： 243-255.
[16] Wen Z X， Liang J W， Liu C Y， et al. Prediction Method for Creep Life of Thin-Wall Specimen with Film Cooling Holes in Ni-Based Single-Crystal Superalloy［J］. International Journal of Mechanical Sciences， 2018， 141： 276-289.
[17] Wen Z X， Huang S， Gao H S， et al. Experimental Investigation on Low Cycle Fatigue Properties of GH3536 Alloy with Film Cooling Holes in Different Drilling Processes［J］. Engineering Failure Analysis， 2017， 82： 190-197.
[18] Zhou Z J， Wang L， Wen J L， et al. Effect of Skew Angle of Holes on the Tensile Behavior of a Ni-Base Single Crystal Superalloy［J］. Journal of Alloys & Compounds， 2015， 628： 158-163.
[19] Weck A， Wilkinson D S. Experimental Investigation of Void Coalescence in Metallic Sheets Containing Laser Drilled Holes［J］. Acta Materialia， 2008， 56（8）： 1774-1784.
[20] Rau C A. Elastic-Plastic Strain Concentrations Produced by Various Skew Holes in a Flat Plate under Uniaxial Tension［J］. Experimental Mechanics， 1971， 11（3）： 133-141.
[21] Liang J W， Wen Z X， Yue Z F. Numerical Simulation on the Creep Damage Evolution of Nickel-Based Single Crystal Specimens with Slant-Angled Film Cooling Holes［J］. Rare Metal Materials and Engineering， 2015， 44（11）： 2656-2660.
[22] Asaro R J. Micromechanics of Crystals and Polycrystals［J］. Advances in Applied Mechanics， 1983， 23（1）： 115.

气膜孔倾角角度对单晶高温合金疲劳性能的影响

Effects of Slant Angle of Film Hole on Fatigue Properties of Single Crystal Superalloy

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价