双组元25N推力器脉冲工作模式下的传热特性分析及改进

doi:10.13675/j.cnki. tjjs. 190348

推进技术 ›› 2020, Vol. 41 ›› Issue (1): 92-100.DOI: 10.13675/j.cnki. tjjs. 190348

双组元25N推力器脉冲工作模式下的传热特性分析及改进

张榛^1,2,3,汪凤山^1,2,蔡坤^1,2,毛晓芳^1,2,杨尚锋^1,2,虞育松⁴

1.北京控制工程研究所，北京 100190;2.北京市高效能及绿色宇航推进工程技术研究中心，北京 100190;3.爱丁堡大学工程学院多尺度热流体研究所，英国;EH9 3FD;4.北京交通大学新能源汽车动力总成技术北京市重点实验室，北京;100044

出版日期:2020-01-20 发布日期:2020-01-20
基金资助:
十二五装备预先研究项目（513200602）；国家留学基金委资助（201804980052）。

Analysis and Improvement of Thermal Conductive Characteristics of Bipropellant 25N Thruster in Pulse Working Mode

1.Beijing Institute of Control Engineering,Beijing 100190,China;2.Beijing Engineering Research Center of Efficient and Green Aerospace Propulsion Technology,Beijing 100190,China;3.Institute of Multiscale Thermofluids,School of Engineering,The University of Edinburgh,EH9 3FD,Scotland UK;4.Beijing Key Lab of New Energy Vehicle Powertrain Technology,Beijing Jiaotong University,Beijing 100044,China

Online:2020-01-20 Published:2020-01-20

摘要/Abstract

摘要： 在离心式双组元25N推力器的脉冲工况温度稳定性试验中，有16%的工况均发生了推力器稳态温度跃迁导致的喷注器头部高温过热的问题。本研究针对该问题开展了深入的机理分析，并通过优化推力器局部传热特性以消除其对于特殊脉冲工况的应用限制和风险。通过液滴撞壁试验，分析了不同条件下推进剂液膜发展的规律和机理：一旦壁面温度达到了莱登弗斯特温度以后，液滴与壁面的换热能力将大幅下降，严重影响液膜冷却的效率。通过Amesim软件进行的传热仿真进一步表明，一旦因为热回浸现象导致雾化液滴与涂层壁面的作用机制发生变化，进而影响冷却液膜的形成，就会使推力器的温度分布从正常的第一稳态进入无液膜的第二高温稳态。仿真结果基本复现了热稳定性试验中出现的故障模式。针对该故障机理改进了喷注器的结构导热性，将喷注器的花篮连接结构的导热面积增加了1.5倍，可以有效分担液膜的热流负担，抑制液膜进入莱登弗斯特态，使得推力器的脉冲工作可靠性大幅提高，令温度稳定性试验的通过率提升至100%。

关键词: 双组元25N推力器;传热;液膜;热稳定性;结构导热性

Abstract: In the thermal stability test of the pulsing condition of 25N bipropellant thruster, 16% of those cases were affected by the high temperature overheating problem of the injector head in the sudden transition of thruster steady-state temperature distribution. This study investigated in-depth mechanism analysis for this problem in order to remove application restrictions and risks in those specific pulse working modes by optimizing the thermal conductive characteristics of the thruster. The droplet impact experiment was carried out to research the development of spray droplets impinging the coating wall under different conditions. Once the cooling film goes into the Leidenfrost state, it can be very difficult to make the effective heat transfer with the hot chamber wall and it influences the efficiency of cooling film. Through the thermal simulation using Amesim, it was clear that the formation of the cooling film of the thruster can be strongly affected due to the variable impact between the atomized droplets and coating wall, under the influence of thermo-soakback phenomena. That can consequently lead to the second plateau state of thruster from the normal first state, which was a recurrence of the failure characteristic in the thermal stability test. According to this mechanism, the structural thermal conductivity of injector was improved by thickening as 1.5 times as the frame connection structure of injector, weakening the heat flux burden of the liquid film to suppress its generation of Leidenfrost state. After improvement, it was validated that the thermal stability and reliability of thruster in the pulse working mode can be enhanced significantly in this way, getting the success rate of thermal stability tests up to 100%.

Key words: Bipropellant 25N thruster;Heat transfer;Liquid film;Thermal stability;Structural thermal conductivity

张榛,汪凤山,蔡坤,毛晓芳,杨尚锋,虞育松. 双组元25N推力器脉冲工作模式下的传热特性分析及改进[J]. 推进技术, 2020, 41(1): 92-100.

ZHANG Zhen^1,2,3,WANG Feng-shan^1,2,CAI Kun^1,2,MAO Xiao-fang^1,2,YANG Shang-feng^1,2,YU Yu-song⁴. Analysis and Improvement of Thermal Conductive Characteristics of Bipropellant 25N Thruster in Pulse Working Mode[J]. Journal of Propulsion Technology, 2020, 41(1): 92-100.

参考文献

[1] 汪凤山, 毛晓芳，虞育松，等. 双组元离心式喷注器雾化性能的大涡模拟数值研究[J]. 空间控制技术与应用， 2012， 38(6): 13-17.
[2] 张榛，虞育松，侯凌云，等. 喷雾液滴与涂层壁面作用的机理性试验及其影响研究[J]. 推进技术， 2019， 40(7): 1562-1569.
[3] Fu Pengfei， Hou Lingyun， Ren Zhuyin， et al. A Droplet/Wall Impact Model and Simulation of a Bipropellant Rocket Engine[J]. Aerospace Science and Technology， 2019， 88(5): 32-39.
[4] 曹顺，陈健，汪凤山. 双组元推力器喷注角度对液膜分布的影响分析[J]. 空间控制技术与应用， 2012， 38(6): 45-49.
[5] 丁佳伟，李国岫，虞育松. 结构参数对双组元推力器喷注器雾化性能影响规律的数值模拟研究[J]. 载人航天， 2015， 6: 635-641.
[6] Gotzig U， Schulte G， Sowa A. New Generation 10N Bipropellant MMH/NTO Thruster with Double Seat Valve[R]. AIAA 99-2594.
[7] 屠善澄. 卫星姿态动力学与控制[M]. 北京:宇航出版社， 2001.
[8] Schulte Georg， Gotzigü Ulrich， Horch Alois， et al. Further Improvements and Qualification Status of Astrium’s 10N Bipropellant Thruster Family[R]. AIAA 2003-4776.
[9] Bai C X， Rusche H， Gosman A D. Modeling of Gasoline Spray Impingement[J]. Atomization & Sprays， 2002， 12(1-3): 1-28.
[10] Bai C. Development of Methodology for Spray Impingement Simulation[J]. SAE International Journal of Engines， 1995， 104(3): 550-568.
[11] Melvin G R, Lin S B. Abriebsbest?ndiger Silicon-überzug für Dichtungsstreifen[P]. Germany: DE19608057, 1996-09.
[12] 张榛，虞育松，符鹏飞，等. 推进剂喷雾液滴与涂层燃烧室壁面作用的机理性试验研究[C]. 洛阳：中国航天第三专业信息网第三十九届技术交流会暨第三届空天动力联合会议， 2018.
[13] 王春海. 基于CLSVOF方法的单液滴碰壁铺展过程的模拟研究[D]. 北京: 北京交通大学， 2011.
[14] Bernardin J D， Stebbins C J， Mudawar I. Mapping of Impact and Heat Transfer Regimes of Water Drops Impinging on a Polished Surface[J]. International Journal of Heat and Mass Transfer， 1997， 40(2): 247-267.
[15] Yao S C， Cai K Y. The Dynamics and Leidenfrost Temperature of Drops Impacting on a Hot Surface at Small Angles[J]. Experimental Thermal and Fluid Science， 1988， 1(4): 363-371.
[16] Bernardin J D， Mudawar I. The Leidenfrost Point: Experimental Study and Assessment of Existing Models[J]. Heat Transfer， 1999， 121(4): 894-903.
[17] Mudawar I， Bernardin J D. A Leidenfrost Point Model for Impinging Droplets and Sprays[J]. Heat Transfer， 2004， 126(2): 272-278.
[18] Baumeister K J， Simon F F. Leidenfrost Temperature: Its Correlation for Liquid Metals， Cryogens， Hydrocarbons， and Water[J]. Heat Transfer， 1973， 95(2): 166-173.

双组元25N推力器脉冲工作模式下的传热特性分析及改进

Analysis and Improvement of Thermal Conductive Characteristics of Bipropellant 25N Thruster in Pulse Working Mode

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价