Investigation on Mass Injection Pre-Cooling Technology of Aero-Turbine Engine

doi:10.13675/j.cnki.tjjs.190445

Journal of Propulsion Technology ›› 2020, Vol. 41 ›› Issue (4): 721-728.DOI: 10.13675/j.cnki.tjjs.190445

• Review • Next Articles

Investigation on Mass Injection Pre-Cooling Technology of Aero-Turbine Engine

1.College of Power and Energy Engineering,Harbin Engineering University,Harbin 150001,China;2.Science and Technology on Altitude Simulation Laboratory,AECC Sichuan Gas Turbine Establishment, Mianyang 621700,China;3.AECC Sichuan Gas Turbine Establishment,Chengdu 610500,China

Published:2021-08-15

航空涡轮发动机射流预冷技术研究

林阿强¹，郑群¹，吴锋^2,3，杨昊³，张海¹

1.哈尔滨工程大学动力与能源工程学院，黑龙江哈尔滨 150001;2.中国航发四川燃气涡轮研究院高空模拟技术重点实验室，四川绵阳 621700;3.中国航发四川燃气涡轮研究院，四川成都 610500

作者简介:林阿强，博士生，研究领域为高速涡轮发动机射流预冷技术。E-mail：linaqiang493@sina.com
基金资助:
国家科技重大专项基金（2017-I-0009-0010；2017-II-0006-0019）；哈尔滨工程大学博士研究生科研创新基金（3072019GIP0304）；中央高校基本科研业务专项基金（3072019CFJ0309）。

Abstract

Abstract: High-temperature inlet air can be reduced to the allowable working temperature of engine material by using the atomization evaporation that is an efficient cooling technology. For mass injection pre-cooling turbine-based ramjet combined cycle engine (MIPCC-TBCC), this study compares and analyzes the development of mass injection pre-compressor cooling (MIPCC) technology existing at home and abroad, introduces the theoretical and experimental verification of MIPCC engine in detail, summarizes the influence of mass injection pre-cooling on engine performance, and studies and verifies the effect of mass injection device and water/ liquid oxygen injection cooling characteristics. All the researches showed that the MIPCC technology will not have too much adverse impact on engine performance. It has the advantages of fast formation, low cost, effective expansion of flight envelope, and is not limited by flight altitude and Mach number. Simultaneously, MIPCC can solve the ‘thrust gap’ problem between turbo-engine and ramjet in the process of mode conversion, which has potential technical advantages. Therefore, MIPCC engine deserves attention and further research.

Key words: Turbine engine;Thrust gap;High-temperature inlet air;Mass injection pre-cooling;Mass injection device

摘要： 利用雾化蒸发的高效冷却技术，可以将高温进气降低到发动机材料允许的工作温度。针对射流预冷涡轮基冲压组合循环发动机，对比分析了国内外已有射流预冷技术的进展，详细介绍了射流预冷发动机的理论和试验验证情况，总结了射流预冷对航空涡轮发动机性能的影响，针对射流装置和喷水/液氧降温效果进行研究和验证。国内外已有研究表明，依靠射流预冷技术不会对发动机性能产生太大的不利影响，具有技术成型快、成本低，有效地扩展飞行包线，不受飞行高度和马赫数限制等优势。射流预冷技术可以解决涡轮发动机与冲压发动机在模态转换过程的“推力鸿沟”问题，具有潜在的技术优势，值得引起关注并开展进一步的深入研究。

关键词: 涡轮发动机;推力鸿沟;高温进气;射流预冷;射流装置

LIN A-qiang¹, ZHENG Qun¹, WU Feng^2,3, YANG Hao³, ZHANG Hai¹. Investigation on Mass Injection Pre-Cooling Technology of Aero-Turbine Engine[J]. Journal of Propulsion Technology, 2020, 41(4): 721-728.

林阿强，郑群，吴锋，杨昊，张海. 航空涡轮发动机射流预冷技术研究[J]. 推进技术, 2020, 41(4): 721-728.

References

[1] Tang M, Chase R L. The Quest for Hypersonic Flight with Air-Breathing Propulsion[R]. AIAA 2008-2546.
[2] Tanatsugu N， Sato T， Naruo Y， et al. Development Study on ATREX Engine[J]. Acta Astronautica， 1997， 40(2-8): 165-170.
[3] Sato T， Tanatsugu N. Development Study of a Precooler for the Air-Turboramjet Expander-Cycle Engine[J]. Journal of Propulsion and Power， 2001， 17(6): 1233-1238.
[4] Burns B R A. HOTOL Space Transport for the Twenty-First Century[J]. Proceedings of the Institution of Mechanical Engineers， Part G: Journal of Aerospace Engineering， 1990， 204(2): 101-110.
[5] Varvill R， Bond A. The SKYLON Spaceplane: Progress to Realisation[J]. Journal of the British Interplanetary Society， 2008， 61(10): 412-418.
[6] Mehta U， Bowles J， Melton J. Water Injection Pre-Compressor Cooling Assist Space Access[R]. AIAA 2012-5922.
[7] 邹正平，刘火星，唐海龙，等. 高超声速航空发动机强预冷技术研究[J]. 航空学报， 2015， 36(8): 2544-2562.
[8] Wang Zhenguo， Wang Yuan， Zhang Jianqiang， et al. Overview of the Key Technologies of Combined Cycle Engine Precooling Systems and the Advanced Applications of Micro-Channel Heat Transfer[J]. Aerospace Science and Technology， 2014， 39: 31-39.
[9] Hall E W， Wilcox E C. Theoretical Comparison of Several Methods of Thrust Augmentation for Turbojet Engines[R]. NACA-RM-E8H11， 1948.
[10] Trout A M. Theoretical Turbojet Thrust Augmentation by Evaporation of Water During Compression as Determined by Use of Mollier Diagrams [R]. NACA-TN-2104， 1950.
[11] Wilcox E C， Trout A M. Analysis of Thrust Augmentation of Turbojet Engines by Water Injection at Compressor Inlet Including Charts for Calculating Compression Processes with Water Injection[R]. NACA-TR-1006， 1951.
[12] Willens D. Liquid Injection on Turbojet Engines for High Speed Aircraft[R]. Propulsion Research Report R-139， 1955.
[13] Sohn R L. Theoretical and Experimental Studies of Pre-Compressor Evaporative Cooling for Application to the Turbojet Engine in High Altitude Supersonic Flight[R]. WADC-TR-56-477， 1956.
[14] King P G， Nygaard R C. Mechanical Operating Experience with Three J-57-P-11 Turbojet Engines During a Pre-Compressor Spray Cooling Test in an Altitude Test Chamber[R]. AEDC-TN-57-70， 1958.
[15] Neely J， Ward T R. Maximum Power Performance of a J57 and a YJ75 Turbojet Engine with Pre-Compressor Water Evaporative Cooling[R]. AEDC-TR-58-18， 1959.
[16] Jones W L， Sivo J N， Wanhainen J P. The Effect of Compressor-Inlet Water Injection on Engine and after Burner Performance[R]. NACA-RM-E58D03B， 1958.
[17] King L D. Design and Testing of a Pre-Compressor Cooling System for a High Speed Aircraft[R]. USA: Chase Vought Corporation， Vought Aeronautics Division， 1961.
[18] Henneberry H， Snyder C. Analyses of Gas Turbine Engines Using Water and Oxygen Injection to Achieve High Mach Numbers and High Thrust[R]. NASA/TM-1993-106270， 1993.
[19] Balepin V. Method and Apparatus for Reducing the Temperature of Air Entering a Compressor of a Turbojet Engine by Variably Injecting Fluid Into the Incoming Air[P]. United States Patent: 6202404， 2001-03-20.
[20] Balepin V， Bruno C， Ingenito A. Evaluation of the Combustion Process in the MIPCC Engine[R]. ISABE 2003-1127.
[21] Carter P， Balepin V. Mass Injection and Precompressor Cooling Engines Analyses[R]. AIAA 2002-4127.
[22] Balepin V， Liston G. The SteamJetTM: Mach 6+ Turbine Engine with Inlet Air Conditioning[R]. AIAA 2001-3238.
[23] Carter P， Balepin V， Spath T， et al. MIPCC Technology Development[R]. AIAA 2003-6929.
[24] 刘月玲，张超. 射流预冷试验温度和湿度测试研究[J]. 测控技术， 2015， 34: 517-519.
[25] 刘旭峰，常鸿雯，薛洪科，等. 射流预冷装置温降与流阻特性试验研究[J]. 航空发动机， 2018， 44(2): 81-86.
[26] Lin Aqiang， Zheng Qun， Hamza Fawzy ， et al. Effect of Water Injection Cooling on Flow Field Characteristics in the Cooling Section of Precooled Turbine-Based Combined Cycle Engine[J]. International Journal of Heat and Mass Transfer， 2019， 141: 615-626.
[27] 涂洪妍，邓远灏，康松，等. 水气比对射流预冷喷射特性影响的数值研究[J]. 推进技术， 2017， 38(6): 1302-1309.
[28] 李艳军，常鸿雯，薛洪科，等. 射流装置降温性能评估及敏感性分析[J]. 航空发动机， 2017， 43(1): 85-90.
[29] Lin Aqiang， Zhou Jie， Fawzy H， et al. Evaluation of Mass Injection Cooling on Flow and Heat Transfer Characteristics for High-Temperature Inlet Air in a MIPCC Engine[J]. International Journal of Heat and Mass Transfer， 2019， 135: 620-630.
[30] Lin Aqiang， Zhou Jie， Tian Xiaojiang， et al. Effective Boundary Conditions and Numerical Method for Flow Characteristics of Aeroengine Compressor at High Mach Flight[J]. Journal of Applied Fluid Mechanics， 2019， 12(3): 845-855.
[31] Lin Aqiang， Zheng Qun， Yang Lu， et al. Effect of Inlet Air Pre-Cooling of Water Injection on Compressor Performance at High Flight Mach[J]. Journal of Applied Fluid Mechanics， 2019， 12(2): 421-431.
[32] 林阿强，郑群，张海，等. 射流冷却对航空发动机压气机的特性分析[J]. 哈尔滨工程大学学报， 2019， 40(9): 1608-1615.
[33] Lin Aqiang， Sun Yonggang， Zhang Hai， et al. Fluctuating Characteristics of Air-Mist Mixture Flow with Conjugate Wall-Film Motion in a Compressor of Gas Turbine[J]. Applied Thermal Engineering， 2018， 142: 779-792.
[34] Lin Aqiang， Zheng Qun， Jiang Yuting， et al. Sensitivity of Air/mist Non-Equilibrium Phase Transition Cooling to Transient Characteristics in a Compressor of Gas Turbine[J]. International Journal of Heat and Mass Transfer， 2019， 135: 882-894.
[35] Walker J， Thomas S， Sorge R. Demonstration of J85-21 Turbojet Operation at Mach 3 Using Pre-Compressor Water Injection[R]. NASA/TM-1999-209397， 1999.
[36] Micheletti DAs. Advanced Aerospace Technology Development at MSE Technology Applications, INC[R]. AIAA 2002-2110.
[37] 杨天宇，张彦军，芮长胜. 高速涡轮发动机技术发展浅析[J]. 燃气涡轮试验与研究， 2013， 26(6): 26-30.
[38] Kloesel K J， Clark C M. Preliminary MIPCC Enhanced F-4 and F-15 Performance Characteristics for a First Stage Reusable Launch Vehicle[R]. AIAA 2013-5528.
[39] Miller J. Peace Jack an Enigma Exposed[J]. Air International， 1985， 7： 18-23.
[40] Carter P O， Brown T R. DARPA’s Rapid Access Small Cargo Affordable Launch(RASCAL)Program[R]. AIAA 2003-8004.
[41] Young D A， Olds J R. Responsive Access Small Cargo Affordable Launch (RASCAL) Independent Performance Evaluation[R]. AIAA 2005-3241.
[42] Mehta U， Bowles J， Melton J， et al. Water Injection Pre-Compressor Cooling Assist Space Access[R]. AIAA 2012-5922.
[43] Balepin B， Ossello C. NO_x Emission Reduction in Commercial Jets Through Water Injection[R]. AIAA 2002-3623.
[44] Balepin V. High Speed Propulsion Cycles[R]. Educational Notes RTO-EN-AVT-150， 2007.
[45] 李刚团，李继保，周人治. 涡轮-冲压组合发动机技术发展浅析[J]. 燃气涡轮试验与研究， 2006， 19(2): 57-62.
[46] 王占学，乔渭阳. 预冷却涡轮基组合循环发动机发展现状及应用前景[J]. 燃气涡轮试验与研究， 2005， 18(1): 53-56.
[47] 芮长胜，张超，越冬峰. 射流预冷涡轮发动机技术研究及发展[J]. 航空科学技术， 2015， 26(10): 53-59.
[48] 尚守堂，田方超，扈鹏飞. 涡轮发动机射流预冷关键技术分析[J]. 航空科学技术， 2018， 29(1): 1-3.

Investigation on Mass Injection Pre-Cooling Technology of Aero-Turbine Engine

航空涡轮发动机射流预冷技术研究

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 0

Recommended Articles

Metrics

Comments