预冷对发动机进气道流动特性影响的数值模拟研究

doi:10.13675/j.cnki.tjjs.190368

推进技术 ›› 2020, Vol. 41 ›› Issue (6): 1227-1236.DOI: 10.13675/j.cnki.tjjs.190368

预冷对发动机进气道流动特性影响的数值模拟研究

薛亮波¹，孙波¹，卓长飞¹，满延进²，李宏东²

1.南京理工大学机械工程学院，江苏南京 210094;2.北京动力机械研究所，北京 100074

发布日期:2021-08-15
作者简介:薛亮波，硕士生，研究领域为高超声速气体动力学。E-mail：424130533@qq.com

Numerical Simulation Study of Effects of Precooling on Flow Characteristics of Engine Inlets

1.School of Mechanical Engineering，Nanjing University of Science and Technology，Nanjing 210094，China;2.Beijing Power Machinery Institute，Beijing 100074，China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究预冷对协同吸气式火箭发动机（Synergetic Air-Breathing Rocket Engine，SABRE）进气道流场性能的影响，以各工况临界状态下无预冷的SABRE发动机进气道为对象，结合多孔介质耦合源项法开展了预冷效应对进气道流动特性影响的数值仿真研究。对比了预冷前后进气道流场及气动性能的变化。研究表明，多孔介质耦合源项法预冷可以较好地模拟预冷器的冷却效应及压降效应，预冷后结尾激波较预冷前向前移动了一段距离，各工况涡轮通道出口总温降低了48%~77%，其中Ma2~4时总温降低到了210K左右；来流空气经预冷后涡轮通道出口马赫数降低，流量系数也随之降低；进气道总压恢复系数呈减小趋势，低速工况总压恢复系数较好，预冷前后两通道总压恢复系数变化不大，涡轮通道流量系数较预冷前降低了约15%。

关键词: SABRE进气道;数值仿真;源项;多孔介质;预冷;压降

Abstract: To study the precooling effect and flow field performance of synergetic air-breathing rocket engine (SABRE) inlet，the SABRE engine inlet without precooling under critical state of each working condition was adopted，and a numerical simulation study of the effects of precooling on the flow characteristics of inlet was carried out in combination with porous media coupling source term. The change of aerodynamic performance of inlet before and after precooling was compared，and the effect of airflow on inlet performance after precooling was explored. Studies indicate that porous media coupled source term method could commendably simulate the cooling effect and pressure drop effect of precooler and the terminal shock wave moves forward a distance after precooling. The total temperature of turbine channel outlet under each working condition decreases by 48%~77%，among which the total temperature at Ma2~4 reduces to around 210K. After precooling the incoming air，the exit Mach number of turbine channel is reduced，and its mass flow ratio also decreases accordingly. The inlet total pressure recovery coefficient tends to decrease，and it is better at low speed condition. The change of total pressure recovery coefficient of the two channels before and after precooling is not obvious. Mass flow ratio of turbine channel is approximately 15% lower than that without precooling.

Key words: SABRE inlet;Numerical simulation;Source term;Porous media;Precooling;Pressure drop

薛亮波，孙波，卓长飞，满延进，李宏东. 预冷对发动机进气道流动特性影响的数值模拟研究[J]. 推进技术, 2020, 41(6): 1227-1236.

XUE Liang-bo¹, SUN Bo¹, ZHUO Chang-fei¹, MAN Yan-jin², LI Hong-dong². Numerical Simulation Study of Effects of Precooling on Flow Characteristics of Engine Inlets[J]. Journal of Propulsion Technology, 2020, 41(6): 1227-1236.

参考文献

[1] Varvill R, Bond A. A Comparison of Propulsion Concepts for SSTO Reusable Launchers[J]. Journal of the British Interpanetary Society, 2003, 56(3-4): 108-117.
[2] Davies R, Bond A. The SKYLON Spaceplane[J]. Journal of the British Interplanetary Society, 1999, 52(1).
[3] Varvill R, Bond A. The SKYLON Spaceplane-Progress to Realisation[J]. Journal of the British Interplanetary Society, 2008, 61(10): 22-32.
[4] Longstaff R, Bond A. The SKYLON Project[C]. Orlando: 17th AIAA International Space Planes and Hypersonic Systems and Technologies Conference, 2011.
[5] 聂万胜, 周思引, 雷旭. 协同吸气式火箭发动机研究进展[J]. 装备学院学报, 2016， (6)： 57-64.
[6] 杨新垒, 聂万胜, 刘晓慧. SABRE吸气模式热力循环及预冷器性能分析[J]. 战术导弹技术, 2018, (1)： 104-110.
[7] Ardema D M, Bowles V J, Whittaker T. Near-Optimal Propulsion System Operation for Air-Breathing Launch Vehicles[R]. AIAA 94-3635-CP.
[8] Roger L, Alan B. The SKYLON Project[R]. AIAA 2011-2244.
[9] 陈静敏, 蒋妮, 郑日恒. SABRE发动机吸气模式下的总体性能分析[C]. 厦门：第五届冲压发动机会议, 2015.
[10] 张建强, 王振国, 李清廉. 空气深度预冷组合循环发动机吸气式模态建模及性能分析[J]. 国防科技大学学报, 2018, 40(1)： 1-9.
[11] Varvill R. Heat Exchanger Development at Reaction Engines Ltd.[J]. Acta Astronautica, 2010, 66(9)： 1468-1474.
[12] Murray J, Hempsell C M, Bond A. An Experimental Precooler for Airbreathing Rocket Engines[J]. Journal of the British Interplanetary Society, 2001, 54(5-6).
[13] 朱岩, 马元, 张蒙正. 预冷组合发动机中微通道换热器的仿真分析[J]. 火箭推进, 2017, 43(2)： 18-24.
[14] 罗佳茂, 杨顺华, 张建强, 等. 换热预冷发动机预冷特性和发动机性能数值研究[J]. 航空学报, 2019, 40(5):1-13.
[15] 魏鑫. 吸气预冷发动机热力循环及预冷器传热特性研究[D]. 南京：南京航空航天大学, 2018.
[16] Wang Z, Wang Y, Zhang J, et al. Overview of the Key Technologies of Combined Cycle Engine Precooling Systems and the Advanced Applications of Micro-Channel Heat Transfer[J]. Aerospace Science and Technology, 2014, 39: 31-39.
[17] 乐嘉陵, 杨顺华, 张建强, 等. TBCC发动机涡轮进气道喷水冷却特性数值研究[J]. 推进技术, 2019, 40(6): 1-10.
[18] 邓彩华, 童亮, 陈壁峰, 等. 多孔介质流动的直接数值模拟[J]. 武汉理工大学学报(交通科学与工程版), 2011, 35(6)： 1257-1260.
[19] 李振鹏. 球床多孔介质通道单相流体流动特性研究[D]. 哈尔滨：哈尔滨工程大学, 2009.

预冷对发动机进气道流动特性影响的数值模拟研究

Numerical Simulation Study of Effects of Precooling on Flow Characteristics of Engine Inlets

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价