超燃冲压发动机多凹腔燃烧室混合与燃烧性能定量分析

推进技术 ›› 2012, Vol. 33 ›› Issue (2): 185-192.

超燃冲压发动机多凹腔燃烧室混合与燃烧性能定量分析

范周琴,刘卫东,孙明波,潘余

国防科学技术大学航天与材料工程学院,湖南长沙 410073;国防科学技术大学航天与材料工程学院,湖南长沙 410073;国防科学技术大学航天与材料工程学院,湖南长沙 410073;国防科学技术大学航天与材料工程学院,湖南长沙 410073

发布日期:2021-08-15
作者简介:范周琴(1983—),女,博士生,研究领域为高超声速推进技术。E-mail:fanzhouqin830227@163.com
基金资助:
国家自然科学基金(50906098;11002159)；高等学校博士点新教师专项科研基金(20094307120005)。

Quantitative Analysis of Mixing and Combustion in the Scramjet Multi-Cavity Combustor

Institute of Aerospace and Material Engineering, National University of Defence Technology, Changsha 410073,China;Institute of Aerospace and Material Engineering, National University of Defence Technology, Changsha 410073,China;Institute of Aerospace and Material Engineering, National University of Defence Technology, Changsha 410073,China;Institute of Aerospace and Material Engineering, National University of Defence Technology, Changsha 410073,China

Published:2021-08-15

摘要/Abstract

摘要： 为从定量上研究超燃冲压发动机多凹腔燃烧室对增强混合、燃烧的影响,用大涡模拟方法和火焰面模型对燃料当量比为0.062的流场进行数值模拟。比较了不同多凹腔构型对混合效率、燃烧效率和总压损失的影响,并结合壁面压力分布、数值纹影解释了其原因。结果表明,凹腔串联、凹腔并联均能增强混合,混合效率最大可提高20.95%和9.52%；凹腔串联、凹腔并联均能增强燃烧,燃烧效率最大可提高14%和16.94%；燃烧时凹腔串联总压损失最小,但凹腔并联燃烧放热最快,对缩短燃烧室长度有利。 

关键词: 超声速湍流燃烧;火焰面模型;多凹腔 

Abstract: In order to determine the influence of multi-cavity on mixing and combustion quantitatively, numerical investigation is carried out in a multi-cavity scramjet chamber with fuel equivalence ratio 0.825 by large eddy simulation and flamelet model. Mixing efficiency, combustion efficiency, and total pressure loss are compared. In addition, wall pressure distribution and numerical schlieren are given to explain the observed results.The analysis shows that the mixing and combustion are improved for cavities mounted in both tandem and parallel. The maximum increase in mixing efficiency can be up to 20.95% and 9.52%, while the combustion efficiency can increase up to 14% and 16.94%. Cavity mounting in tandem has the least total pressure loss in reacting case, while cavity mounting in parallel has the fast heat release, which is good for shortening chamber length.

Key words: Supersonic turbulent combustion; Flamelet model; Multi-cavity

范周琴,刘卫东,孙明波,潘余. 超燃冲压发动机多凹腔燃烧室混合与燃烧性能定量分析[J]. 推进技术, 2012, 33(2): 185-192.

参考文献

[2] Roudakov A S,Schikhmann Y,Semenov V,et al．Flight Testing of an Axisymmetric Scramjet －Russian Recent Advances[R]．International Astronautical Federation,93-S4.
[3] Vinagradov V,Kobigsky S A,Petrov MD．Experimental Investigation of Kerosene Fuel Combustion in Supersonic Flow[J]．Journal of Propulsion and Power,1995,11(1):130-134.
[4] 潘余.超燃冲压发动机多凹腔燃烧室燃烧与流动过程研究 [D].长沙:国防科学技术大学,2007.
[5] 刘娟,潘余,刘卫东,等.超燃冲压发动机燃烧室中双凹腔对引导氢分布的影响[J].国防科大学报,2009,31(2).
[6] 刘娟,潘余,刘卫东,等.超燃冲压发动机双凹腔燃烧室氢气燃烧流场分析[J].航空动力学报,2009,24(11).
[7] 李大鹏．煤油双模态冲压发动机燃烧室工作过程研究[D]．长沙:国防科学技术大学,2006.
[8] Peters N.Laminar Diffusion Flamelet Models in Non-premixed Turbulent Combustion [J].Prog.Energy Combust.Sci,1984,10:319-339.
[9] 刑建文.化学平衡假设和火焰面模型在超燃冲压发动机数值模拟中的应用 [D].绵阳:中国空气动力研究与发展中心,2007.
[10] 刑建文,乐嘉陵.火焰面模型在超燃冲压发动机数值模拟中的应用 [J].实验流体力学,2008,22(2).
[11] 杨阳,刑建文.湍流燃烧模型对氢燃料超燃室流场模拟的影响 [J].航空动力学报,2008,23(4).
[12] Pitch H.Enteicklung Cines Programmpaketes Zur Berechnung Eindimensionaler Flammen am Beispiel Einer Gegenstromdiffusions Flamme[D].Aachen:Institut fur Technische Mechanik,1993.
[13] Mass U, Warnatz J.Ignition Processes in Hydrogen Oxygen Mixtures[J].Combust Flame,1988,74:53-69.
[14] Terrapon V E, Ham F, Pecnik R, et al.A Flamelet-based Model for Supersonic Combustion[R].Center for Turbulence Research,Annual Research Briefs, 2009.
[15] 孙明波.超声速来流稳焰凹腔的流动及火焰稳定机制研究 [D].长沙:国防科学技术大学,2008.
[16] Baurle R A, Eklund D R, Gruber M R, Numerical Study of Scramjet Combustor Fueled by Aerodynamic Ramp Injector in Dual Mode Combustion[R].AIAA 2001-0379.
[17] Rajasekaran A, Babu V.Numerical Simulation Three Dimensional Reacting Flow in a Model Supersonic Combustor[J].Journal of Propulsion and Power, 6,2(4).
[18] 范周琴,孙明波,刘卫东.基于火焰面模型的超声速燃烧混合LES/RANS模拟 [J] .推进技术,1,2(2):191-196.(FAN Zhou-qin,SUN Ming-bo,LIU Wei-dong.Hybrid LES/RANS Simulation of Supersonic Combustion using Flamelet Model [J].Journal of Propulsion Technology, 1,2(2):191-196.)
[19] Jeong J, Hussain F.On the Identification of a Vortex [J].Journal of Fluid Mechanics, 5,5:69-94.