级间通道构型对双脉冲发动机燃烧室局部受热的影响

推进技术 ›› 2014, Vol. 35 ›› Issue (11): 1503-1510.

级间通道构型对双脉冲发动机燃烧室局部受热的影响

李映坤¹,韩珺礼^1,2,陈　雄¹,刘　锐¹

南京理工大学机械工程学院，江苏南京 210094;南京理工大学机械工程学院，江苏南京 210094; 北京机电研究所，北京 100012;南京理工大学机械工程学院，江苏南京 210094;南京理工大学机械工程学院，江苏南京 210094

发布日期:2021-08-15
作者简介:李映坤(1989—)，男，博士生，研究领域为航空宇航推进理论与工程。

Effects of Two-Stage Pulse Channel Configurations on Local Heat Transfer Characteristics in Combustion Chamber of Dual Pulse Motor

School of Mechanical Engineering，Nanjing University of Science and Technology，Nanjing 210094，China;School of Mechanical Engineering，Nanjing University of Science and Technology，Nanjing 210094，China; Beijing Institute of Electromechanical Technology，Beijing 100012，China;School of Mechanical Engineering，Nanjing University of Science and Technology，Nanjing 210094，China;School of Mechanical Engineering，Nanjing University of Science and Technology，Nanjing 210094，China

Published:2021-08-15

摘要/Abstract

摘要： 为研究级间通道构型对双脉冲发动机一脉冲燃烧室气流再附着点的位置和对流换热系数的影响，本文采用基于格心的迎风型有限体积法数值求解雷诺平均Navier-Stokes方程组，空间离散采用AUSM-PW矢通量分裂格式，时间推进采用3阶三步TVD型Runge-Kutta显式方法，湍流模型采用适合模拟分离流动的改进SST湍流模型，并通过经验公式计算再附着点处的对流换热系数。结果表明:亚声速后台阶流动和固体火箭发动机燃烧室内流动的最大绝对误差分别为8.9%和5.8%；二脉冲工作的不同时刻，当二脉冲装药内孔直径大于级间通道直径时，级间孔直径每增大9.1%，气流再附着点位置平均减小28.2%，对流换热系数平均下降9.6%；其它条件相同时，级间孔宽度增加对气流再附着点位置和对流换热的影响比较小；级间孔角度变大使得气流再附着点的位置和对流换热系数分别平均下降3.4%和3.1%。

关键词: 双脉冲发动机；内流场；数值分析

Abstract: In order to study the effects of two-stage pulse channel configurations on reattachment location and relative convective heat transfer coefficient in combustion chamber of dual pulse motor，the Reynolds-average Navier-Stokes equations were solved with three-order three-step Runge-Kutta iterative algorithm by cell center upwind finite volume method and AUSM-PW scheme were implemented for spatial discretization. Also，modified SST (shear-stress-transport) turbulence model that improved the capability of predicting separation was used to simulate the turbulence flow. The results show that the maximum absolute error of subsonic flow over backward facing step and solid rocket motor combustion chamber flow are within 8.9% and 5.8%，respectively. During the second pulse phase，when the inner diameter of the second grain larger than the one of the pulse channel，as the diameter of pulse channel increases by 9.1%，the reattachment location and relative convective heat transfer coefficient decrease by an average of 28.2% and 9.6%，respectively. When the other conditions are constant，as the channel angle increases，the reattachment location and relative convective heat transfer coefficient reduce by about 3.4% and 3.1% in average，respectively while the value varies slightly with increasing the pulse channel width.

Key words: Dual pulse motor；Inner flow field；Numerical analysis

李映坤,韩珺礼,陈　雄,刘　锐. 级间通道构型对双脉冲发动机燃烧室局部受热的影响[J]. 推进技术, 2014, 35(11): 1503-1510.

LI Ying-kun¹,HAN Jun-li^1,2,CHEN Xiong¹,LIU Rui¹. Effects of Two-Stage Pulse Channel Configurations on Local Heat Transfer Characteristics in Combustion Chamber of Dual Pulse Motor[J]. Journal of Propulsion Technology, 2014, 35(11): 1503-1510.

参考文献

[1] 叶定友, 王敬超. 固体发动机多次启动技术及应用[J].推进技术, 1989, 10(4):71-74.(YE Ding-you, WANG Jing-chao. Investigation and Application Analysis of Multi-Start Technology in Solid Rocket Motor [J]. Journal of Propulsion Technology, 1989, 10 (4):71-74.)
[2] Naumann K W, Stadler L. Double-Pulse Solid Rocket Motor Technology-Applications and Technical Solutions[R]. AIAA 2010-6754.
[3] 王伟, 李江, 王春光, 等. 隔舱式双脉冲发动机金属膜片设计与实验研究[J]. 推进技术, 2013, 34(8):1115-1120. (WANG Wei, LI Jiang, WANG Chun-guang, et al. Study on Metal Diaphragm of Pulse Separation Device in Dual-Pulse Solid Rocket Motor [J]. Journal of Propulsion Technology, 2013, 34(8):1115-1120.)
[4] 刘亚冰, 王长辉, 刘宇. 双脉冲发动机燃烧室局部烧蚀特性分析[J]. 固体火箭技术, 2011, 34(4):453-456.
[5] 朱卫兵, 张永飞, 陈宏, 等. 双脉冲发动机内流场研究[J]. 弹箭与制导学报, 2012, 32(1):114-118.
[6] 孙娜, 娄永春, 孙长宏, 等. 某双脉冲发动机燃烧室两相流场数值分析[J]. 固体火箭技术, 2012, 35(3):335-338.
[7] Chang-Hui Wang, Yu Liu, Ya-Bing Liu. Design and Experimental Studies on Ceramic Port Cover for Dual Pulse Motor [J]. Acta Astronautica, 2011, 68(11):1881-1890.
[8] 王春光, 田维平, 杨德敏, 等. 脉冲发动机中隔层传热炭化模型[J]. 推进技术, 2012, 33(2):259-262. (WANG Chun-guang, TIAN Wei-ping, YANG De-min, et al. Charring Model of Heat Transfer for Pulse Separation Device of Pulse Motor [J]. Journal of Propulsion Technology, 2012, 33(2):259-262.)
[9] 王春光, 田维平, 任全彬, 等. 脉冲发动机中隔层工作过程的数值分析及试验[J]. 推进技术, 2012, 33(5):790-794. (WANG Chun-guang, TIAN Wei-ping, REN Quan-bin, et al. Numerical Analysis and Test on Work Process of Pulse Separation Device in Pulse Motor [J].Journal of Propulsion Technology, 2012, 33(5):790-794.)
[10] Menter F R. Two-Equation Eddy-Viscosity Turbulence Models for Engineering Applications [J]. AIAA Journal, 1994, 32(08):1598-1605.
[11] 甘文彪, 周洲, 许晓平, 等. 基于改进SST模型的分离流动数值模拟[J]. 推进技术, 2013, 34(5):595-602. (GAN Wen-biao, ZHOU Zhou, XU Xiao-ping, et al. Investigation on Improving the Capability of Predicting Separation in Modified SST Turbulence Model [J].Journal of Propulsion Technology, 2013, 34(5):595-602.)
[12] Meng Sing Liou. Methods for the Accurate Computations of Hypersonic Flows [J]. Journal of Computational Physics, 2001, 174(01):38-80.
[13] Schilling S, Trouillot P, Weigand A. On the Development and Testing of a 120mm Caliber Double Pulse Motor [R]. AIAA 2004-3387.
[14] Arabshahi A, Webster R S, Briley W R, et al. Numerical Analysis of Solid Propellant Rocket Motor Internal Flows[R]. AIAA 2006-5114.
[15] Sachdev J S. Parallel Solution-Adaptive Method for Predicting Solid Propellant Rocket Motor Core Flows [D]. Toronto: University of Toronto, 2007.
[16] Shisnov E V, Roganov P S, Grabarnik S I, et al. Heat Transfer in the Recirculating Region Formed by a Backward-Facing Step [J].International Journal of Heat and Mass Transfer, 1988, 31(8):1557-1562.
[17] Driver D M, Seegmiller H L. Features of a Reattaching Turbulent Shear Layer in Divergent Channel Flow [J]. AIAA Journal, 1985, 23(2):163-171.
[18] Dunlap R, Blackner A M, Waugh R C, et al. Internal Flow Field Studies in a Simulated Cylindrical Port Rocket Chamber [J].Journal of Propulsion and Power, 1990, 6(6): 690-704.(编辑:梅瑛)　　　　　　　　　　　　　　收稿日期:2013-10-28；修订日期:2013-12-20。作者简介:李映坤(1989—),男,博士生,研究领域为航空宇航推进理论与工程。E-mail:lyk1007@126.com