不同横斜槽结构对气膜冷却效果影响的正交模拟

推进技术 ›› 2016, Vol. 37 ›› Issue (5): 922-929.

不同横斜槽结构对气膜冷却效果影响的正交模拟

张玲,王冲

东北电力大学能源与动力工程学院，吉林吉林 132012,东北电力大学能源与动力工程学院，吉林吉林 132012

发布日期:2021-08-15
作者简介:张玲，女，博士，教授，研究领域为流体机械内流的数值与实验研究。
基金资助:
吉林省科技发展计划项目(20130101046JC)。

Orthogonal Simulation of Effects of Different Transverse

School of Energy and Power Engineering，Northeast Dianli University，Jilin 132012，China and School of Energy and Power Engineering，Northeast Dianli University，Jilin 132012，China

Published:2021-08-15

摘要/Abstract

摘要： 通过FLUENT软件并采用Realizable k-ε紊流模型对三维定常不可压缩N-S方程进行求解，利用正交模拟的方法模拟了不同的槽宽、吹风比和槽深三个影响因素共同作用下的平板气膜冷却效果，最终选出最优的冷却方案。结果表明:开槽深度为1倍孔径，吹风比为2.0和开槽宽度为2倍孔径的开槽姊妹孔的冷却效果最佳，为最优冷却方案。槽宽对平板冷却效率的影响最大，槽深的影响较小，吹风比的影响最小；开槽深度为0.75倍孔径，吹风比为2.0和开槽宽度为4倍孔径的开槽姊妹孔的冷却效率最低为0.1974，比最优冷却方案低约173%；横斜槽的存在使反向漩涡对的强度受到了抑制，从而加强了冷却效果。

关键词: 气膜冷却；正交模拟；吹风比；冷却效率；横斜槽

Abstract: The three-dimensional steady incompressible Navier-Stokes equation was solved with Realizable k-ε turbulence model by FLUENT. Cooling effectiveness was analyzed with orthogonal simulation techniques on the effects of the width of groove，blowing ratio and the depth of groove under the combined action. Finally，the best effect of cooling case was chosen. The results show that cooling effect of groove sister hole with depth being one time hole diameter，blowing ratio being 2.0 and groove sister hole with width being two times hole diameter was the best. It was the best cooling case. The effect of the width of groove on cooling efficiency is the biggest and the effect of blowing ratio is much smaller than the depth of groove. The lowest cooling effectiveness of groove sister hole with depth being 0.75 time hole diameter，blowing ratio being 2.0 and groove sister hole with width being four times hole diameter was 0.1974. It is 173% lower than that of the best cooling case. The counter rotating vortex pairs have been weakened for the transverse declining slot and the cooling effect was enhanced.

Key words: Film cooling；Orthogonal simulation；Blowing ratio；Cooling effectiveness；Transverse declining slot

张玲,王冲. 不同横斜槽结构对气膜冷却效果影响的正交模拟[J]. 推进技术, 2016, 37(5): 922-929.

ZHANG Ling ,WANG Chong. Orthogonal Simulation of Effects of Different Transverse[J]. Journal of Propulsion Technology, 2016, 37(5): 922-929.

参考文献

[1] 葛绍岩, 刘登瀛, 徐靖中. 气膜冷却[M]. 北京:科学出版社, 1985.
[2] 戴萍, 林枫. 横向槽结构对气膜冷却效果影响的数值模拟[J]. 推进技术, 2011, 32(2): 253-260. (DAI Ping, LIN Feng. Numerical Investigation on the Influence of Transverse Slot Configurations on Film Cooling Effect[J]. Journal of Propulsion Technology, 2011, 32(2): 253-260.)
[3] 胡雅骥, 程相飞, 于锦禄. 横向槽宽度对气膜孔冷却性能数值研究[J]. 机械设计与制造, 2009, (4): 18-20.
[4] 左红, 王鹏, 武卫, 等. 横向槽深度对气膜孔冷却性能影响数值研究[J]. 机械科学与技术, 2008, 27(9): 1252-1260.
[5] 于锦禄, 赵罡, 何立明, 等. 横向槽横向宽度对气膜孔冷却性能影响的数值研究[J]. 中国电机工程学报, 2010, 30(17): 79-84.
[6] 于锦禄, 何立明, 蒋永健, 等. 带横向槽的气膜冷却结构冷却性能数值研究[J]. 机械设计与制造, 2008,(3): 128-130.
[7] 章大海, 陈秋炀, 曾敏, 等. 不同横槽结构对气膜冷却效率影响的数值研究[J]. 航空动力学报, 2008, 23(4): 611-616.
[8] 陈鑫, 何立明, 于锦禄, 等. 利用横向槽改善气膜冷却效率的实验[J]. 航空动力学报, 2010, 25(2):291-294.
[9] 蒋永健, 何立明, 于锦禄, 等. 利用横向槽改善气膜冷却效率的数值研究[J]. 推进技术, 2008, 29(3):286-289. (JIANG Yong-jian, HE Li-ming , YU Jin-lu, et al. Numerical Investigation on Improving Film Cooling Effectiveness with Transverse Slots[J]. Journal of Propulsion Technology, 2008, 29(3): 286-289.)
[10] 李军, 董志锐, 林宇震, 等. 多斜孔气膜冷却壁表面换热系数实验研究[J]. 推进技术, 2000, 21(5):45-48. (LI Jun, DONG Zhi-rui, LIN Yu-zhen, et al. Experimental Investigation of Heat Transfer Coefficients on the Inclined Multihole Film Cooling Wall[J]. Journal of Propulsion Technology, 2000, 21(5): 45-48.)
[11] 刘宁, 孙纪宁. 不同来流条件下旋转对气膜冷却的影响[J]. 推进技术, 2011, 32(5): 706-712. (LIU Ning, SUN Ji-ning. Effect of Rotation on Film Cooling under Different Inflow Conditions[J]. Journal of Propulsion Technology, 2011, 32(5): 706-712. )
[12] 杨卫华, 马国锋, 张靖周, 等. 气膜冷却孔几何结构对流量系数的影响[J]. 推进技术, 2005, 26(5): 413-416. (YANG Wei-hua, MA Guo-feng, ZHANG Jing-zhou, et al. Influence of Geometrical Construction of Film Cooling Hole on Discharge Coefficient[J]. Journal of Propulsion Technology, 2005, 26(5): 413-416.)
[13] 朱延鑫, 谭晓茗, 郭文, 等. 出流孔型对平板气膜冷却影响机理的研究[J]. 推进技术, 2013, 34(4):499-505. (ZHU Yan-xin, TAN Xiao-ming, GUO Wen, et al. Numerical Simulation on Effects of Different Film Cooling Holes on Plate[J]. Journal of Propulsion Technology, 2013, 34(4): 499-505.)
[14] Habeeb Idowu Oguntade, Gordon E Andrews A D, Burns Derek B Ingham, et al. Improved Trench Film Cooling with Shaped Trench Outlets[J]. Journal of Turbomachinery, 2013, 135(2): 1-10.
[15] Satoshi Hada, Karen A Thole. Computational Study of a Midpassage Gap and Upstream Slot on Vane Endwall Film-Cooling[J]. Journal of Turbomachinery, 2011, 133(1): 1-9.
[16] Sima Baheri Islami, Alavi Tabrizi S P, Jubran B A. Computational Investigation of Film Cooling from Trenched Holes near the Leading Edge of a Turbine Blade[J]. Numerical Heat Transfer, 2008, 53: 308-322.
[17] Joshua E Bruce-Black, Frederick T Davidson, David G Bogard, et al. Practical Slot Configurations for Turbine Film Cooling Applications[J]. Journal of Turbomachinery, 2011, 133(7): 1-8.
[18] Ely M J, Jubran B A. A Numerical Evaluation on the Effect of Sister Holes on Film Cooling Effectiveness and the Surrounding Flow Field[J]. Heat and Mass Transfer, 2009, 45(11): 1435-1446.
[19] Gartshore I, Salcudean M, Hassan I. Film Cooling Injection Hole Geometry: Hole Shape Comparison for Compound Cooling Orientation[J]. AIAA Journal, 2001, 39(8): 1493-1499.
[20] 刘瑞江, 张业旺, 闻崇炜, 等. 正交试验设计和分析方法研究[J]. 实验技术与管理, 2010, 27(9): 52-55.(编辑:史亚红)　　　　　　　　　　　　　*　收稿日期:2014-12-25；修订日期:2015-01-21。基金项目:吉林省科技发展计划项目(20130101046JC)。作者简介:张玲,女,博士,教授,研究领域为流体机械内流的数值与实验研究。E-mail: zhangling_2009@qq.com