侧向膨胀对单边膨胀喷管性能的影响研究

推进技术 ›› 2017, Vol. 38 ›› Issue (3): 519-524.

侧向膨胀对单边膨胀喷管性能的影响研究

牛彦沣,徐惊雷,莫建伟

南京航空航天大学能源与动力学院江苏省航空动力系统重点实验室，江苏南京 210016,南京航空航天大学能源与动力学院江苏省航空动力系统重点实验室，江苏南京 210016,南京航空航天大学能源与动力学院江苏省航空动力系统重点实验室，江苏南京 210016

发布日期:2021-08-15
作者简介:牛彦沣，女，硕士生，研究领域为发动机内流气体动力学。
基金资助:
南京航空航天大学研究生创新基地(实验室)开放基金(kfjj20150203)。

Investigation of Effects of Lateral Expansion on Performance of Single Expansion Ramp Nozzle

Nanjing University of Aeronautics and Astronautics，Jiangsu Province Key Laboratory of Aerospace Power System， Nanjing 210016，China,Nanjing University of Aeronautics and Astronautics，Jiangsu Province Key Laboratory of Aerospace Power System， Nanjing 210016，China and Nanjing University of Aeronautics and Astronautics，Jiangsu Province Key Laboratory of Aerospace Power System， Nanjing 210016，China

Published:2021-08-15

摘要/Abstract

摘要： 为研究侧向膨胀规律的变化对单边膨胀喷管性能的影响规律，运用三次曲线参数化方法给定不同的侧向膨胀规律，基于准二维特征线法设计得到相应的带侧向膨胀的三维非对称喷管构型，结合CFD计算结果，分析了直侧壁和曲侧壁两类侧壁型线对喷管性能的影响规律。为验证数值模拟方法的可靠性，选取具有10°膨胀角的直侧壁喷管进行风洞试验，数值模拟结果与实验结果吻合较好。研究结果表明:在给定的设计条件下，侧向膨胀角为6°时直侧壁喷管性能最优，该膨胀角可使喷管长度减短34.05%。侧向膨胀在保证喷管推力性能的同时，对减短喷管长度、减轻喷管重量具有重要意义；曲侧壁喷管侧壁面产生的推力变化趋势与整个喷管构型产生推力的变化趋势一致；“凸曲线”侧壁型线初始膨胀角较大，更有利于提高三维尾喷管的推力性能。

关键词: 三维非对称喷管；侧向膨胀；喷管性能；风洞试验

Abstract: In order to investigate the effects of lateral expansion on the performance of single expansion ramp nozzle，different laws of lateral expansion were given by using cubic parametric approach，and the corresponding three-dimensional asymmetric nozzle configurations with lateral expansion were designed based on the quasi two-dimensional method of characteristics(MOC). Combined with CFD results，the effects of straight sidewalls and curved sidewalls on the performance of nozzle were further investigated. In order to verify the reliability of numerical simulation method，a cold flow wind tunnel experiment of the nozzle with 10° straight sidewalls was carried out. The results of the simulation are in good agreement with experiment data. The results show that，in the given design conditions，the nozzle with 6° straight sidewalls has optimal performance，and the nozzle’s length can be shortened by 34.05%. Lateral expansion can not only guarantee the performance of nozzle，but also be of great significance to shorten the length of nozzle and reduce its weight. For curved-sidewall nozzles，the trend of the thrust produced by sidewall is consistent with the thrust produced by the whole nozzle configuration. “Convex curve”is more helpful to improve the thrust performance of nozzle because of the larger initial expansion angle.

Key words: Three dimensional asymmetrical nozzle；Lateral expansion；Nozzle performance；Wind tunnel test

牛彦沣,徐惊雷,莫建伟. 侧向膨胀对单边膨胀喷管性能的影响研究[J]. 推进技术, 2017, 38(3): 519-524.

NIU Yan-feng,XU Jing-lei,MO Jian-wei. Investigation of Effects of Lateral Expansion on Performance of Single Expansion Ramp Nozzle[J]. Journal of Propulsion Technology, 2017, 38(3): 519-524.

参考文献

[1] 谭杰, 金捷, 杜刚, 等. 单边膨胀喷管试验和数值模拟[J]. 航空动力学报, 2011, 26(6): 1223-1230.
[2] Mitani T, Ueda S, Tani K, et al. Validation Studies of Scramjet Nozzle Performance[J]. Journal of Propulsion and Power, 1993, 9(5): 725-730.
[3] Baucco A R, Shanley K T, Bevies D. CFD Validation Study for Internal Performance of Advanced SERN Configurations[R]. AIAA 2012-4223.
[4] Novelli P, Koschel W. Progress of the JAPHAR Cooperation between ONERA and DLR on Hypersonic Airbreathing Propulsion[R]. AIAA 2001-1870.
[5] 汪维娜, 王占学, 乔渭阳. 单斜面膨胀喷管几何参数对流场和性能的影响[J]. 航空动力学报, 2006, 21(2): 280-284.
[6] 庞丽娜, 徐惊雷, 范志鹏. 单边膨胀尾喷管下壁面型线优化设计及实验研究[J]. 推进技术, 2014, 35(10): 1297-1302. (PANG Li-na, XU Jing-lei, FAN Zhi-peng. Optimization Design and Experimental Study of Cowl Configuration of SERN[J]. Journal of Propulsion Technology, 2014, 35(10): 1297-1302.)
[7] 全志斌, 徐惊雷, 莫建伟. 基于控制壁面压力分布的分级单边膨胀喷管设计及试验验证[J]. 推进技术, 2013, 34(3): 307-310. (QUAN Zhi-bin, XU Jing-lei, MO Jian-wei. Design and Experiment Validation of Single Expansion Ramp Nozzle Based on the Control of Wall Pressure Distribution[J]. Journal of Propulsion Technology, 2013, 34(3): 307-310.)
[8] 赵强, 徐惊雷, 于洋. 基于膨胀度可控的 SERN 设计及试验验证[J]. 航空学报, 2014, 35(1): 125-131.
[9] Delguidice P, Dash S, Kalben P. A Source Flow Characteristic Technique for the Analysis of Scramjet Exhaust Flow Field[R]. NASA CR-132437, 1974.
[10] Marathe A G, Thiagarajan V. Effect of Geometric Parameters on the Performance of Single Expansion Ramp Nozzle[R]. AIAA 2005-4429.
[11] 高太元, 崔凯, 王秀平, 等. 三维后体/尾喷管一体化构型优化设计及性能分析[J]. 科学通报, 2012, 57(4): 239-247.
[12] 徐大军, 陈兵, 蔡国飙, 等. 高超声速飞行器后体喷管三维构型设计[J]. 航空动力学报, 2009, 24(2):247-254.
[13] 莫建伟. TBCC排气系统设计方法及流场特性研究[D]. 南京:南京航空航天大学, 2015.
[14] (美)左克罗M J, 霍夫曼J D. 气体动力学[M]. 魏叔如, 吴宗善, 王汝涌, 等译. 北京:国防工业出版社, 1984.
[15] Harloff G J, Redy D R, Lai H T. Viscous Three-Dimensional Analyses for Nozzles for Hypersonic Propulsion[R]. NASA CR-185197, 1990.
[16] Goeing M. Nozzle Design Optimization by Method-of-Characteristics[R]. AIAA 90-2024.　　　　　　　　　　　　　　收稿日期:2015-11-25；修订日期:2016-01-29。基金项目:南京航空航天大学研究生创新基地(实验室)开放基金(kfjj20150203)。作者简介:牛彦沣,女,硕士生,研究领域为发动机内流气体动力学。E-mail: yanfengniu@163.com(编辑:史亚红)