气膜-发散组合冷却结构换热特性的实验研究

推进技术 ›› 2018, Vol. 39 ›› Issue (8): 1771-1779.

气膜-发散组合冷却结构换热特性的实验研究

田美¹,冯晓星²,石蕊³,邓向阳²,杨卫华¹

南京航空航天大学能源与动力学院，江苏南京 210016,中国航发商用航空发动机有限公司，上海 200241,空间物理重点实验室，北京 100076,中国航发商用航空发动机有限公司，上海 200241,南京航空航天大学能源与动力学院，江苏南京 210016

发布日期:2021-08-15
作者简介:田美，女，硕士生，研究领域为飞机发动机热端部件冷却技术。E-mail: tianmeinuaa@163.com 通讯作者:杨卫华，男，博士，教授，研究领域为飞机发动机热端部件热防护技术。
基金资助:
国家自然科学基金(51276088)。

Experimental Investigation on Heat Transfer Characteristicsof Film-Effusion Combined Cooling

College of Energy and Power Engineering，Nanjing University of Aeronautics and Astronautics，Nanjing 210016，China,AECC Commercial Aircraft Engine Co.Ltd?，Shanghai 200241，China,Science and Technology on Space Physics Laboratory，Beijing 100076，China,AECC Commercial Aircraft Engine Co.Ltd?，Shanghai 200241，China and College of Energy and Power Engineering，Nanjing University of Aeronautics and Astronautics，Nanjing 210016，China

Published:2021-08-15

摘要/Abstract

摘要： 为了研究气膜-发散组合冷却结构的冷却特征，保证相同的开孔率，设计了三种不同发散孔排布形式的组合冷却结构，采用实验的方法对气动参数和几何参数对绝热冷却效率和对流换热系数的影响规律开展了研究。结果表明:绝热冷却效率和对流换热系数沿主流方向先逐渐降低，达到最低点后沿流动方向二者基本保持不变；在研究参数范围内，主流雷诺数和吹风比对绝热冷却效率的影响不大，但对组合冷却结构的对流换热系数影响较大，随着主流雷诺数和吹风比的增加，对流换热系数均呈现逐渐增大的趋势；针对三种发散孔排布形式的绝热冷却效率和对流换热系数，流向间距大的气膜发散冷却结构最高，流向间距居中的气膜发散冷却结构次之，流向间距最小的气膜发散冷却结构最低。

关键词: 航空发动机；火焰筒冷却；气膜-发散组合冷却；绝热冷却效率；对流换热系数

Abstract: In order to study the cooling characteristics of film-effusion combination cooling structure， three kinds of test pieces of different effusion cooling holes arrangement but equivalent orifice area were designed. The effects of aerodynamic parameters and geometric parameters on the adiabatic cooling efficiency and the convective heat transfer coefficient were investigated experimentally. The experimental results show that the adiabatic cooling efficiency and convective heat transfer coefficient gradually decrease in the direction of mainstream， and reache the lowest point， then they remain unchanged. The main flow Reynolds number and the blowing ratio have no evident effect on the adiabatic cooling efficiency under research range of parameters， but the effect on convective coefficient is evident， that is increased gradually with the increase of main flow Reynolds number or blowing ratio. For the three test specimens， the adiabatic cooling efficiency and the convective coefficient of the cooling structure of the largest stream wise spacing are the largest， and followed by the cooling structure of medium stream wise spacing， and the minimum is the cooling structure of the minimum stream wise spacing.

Key words: Aeroengine；Combustion cooling；Film-effusion cooling；Adiabatic cooling effectiveness；Convective heat transfer coefficient

田美,冯晓星,石蕊,邓向阳,杨卫华. 气膜-发散组合冷却结构换热特性的实验研究[J]. 推进技术, 2018, 39(8): 1771-1779.

TIAN Mei¹,FENG Xiao-xing²,SHI Rui³,DENG Xiang-yang²,YANG Wei-hua¹. Experimental Investigation on Heat Transfer Characteristicsof Film-Effusion Combined Cooling[J]. Journal of Propulsion Technology, 2018, 39(8): 1771-1779.

参考文献

[1] Lefebvre A H. Gas Turbine Combustion[M]. New York: Hemisphere Publishing Corporation, 1983.
[2] Meller A M. Design of Modern Turbine Combustor [M] . New York: Academic Press Inc., 1990.
[3] 李彬, 吉洪湖, 江义军, 等. 浮动壁火焰简壁温试验和计算分析[J]. 南京航空航天大学学报(自然科学版), 2007, 39(6): 771-774.
[4] 杨卫华, 彭建勇, 曹俊, 等. 回流燃烧室复合冷却结构冷却效果研究[J]. 南京航空航天大学学报(自然科学版), 2012, 44(12): 771-774.
[5] Yang Wei-hua, Zhang Jing-zhou. Experimental Study of HTC for Film Cooling of Parallel-Inlet Holes[J]. Transaction of Nanjing University of Aeronautics and Astronautics, 2012, 29(1): 46-53.
[6] Rhee D H, Choi J H, Cho H H. Heat (Mass) Transfer on Effusion Plate in Impingement/Effusion Cooling Systems[J]. Journal of Thermophysics and Heat Transfer, 2003, 17(1): 95-102.
[7] Rhee D H, Choi J H, Cho H H. Flow and Heat (Mass) Transfer Characteristics in an Impingement/Effusion Cooling System with Crossflow[J]. Journal of Turbomachinery, 2003, 125(1): 74-82.
[8] Hollwarth B R, Dagan L. Arrays of Impinging Jets with Spent Fluid Removal through Vent Holes on the Target Surface, Part 1: Average Heat Transfer[J]. Journal of Engineering for Power, 1980, 102: 994-999.
[9] 杨卫华, 王立, 宋双文. 冲击发散冷却流场结构PIV测量[J]. 航空动力学报, 2010, 25(3): 483-487.
[10] Yang Wei-hua, Cao Jun, Shi Rui, et al. Experimental Investigation on Impingement-Effusion Film-Cooling Behaviors in Curve Section[J]. Acta Astronautica,2011, 68(11-12): 1782-1789.
[11] Zhong Fengquan, Brown G. A Three-Dimensional Coupled Heat Transfer Model for Multi-Hole Cooling and Comparisons with Experiments[R]. AIAA 2006-595.
[12] 李广超, 朱惠人, 白江涛, 等. 气膜孔布局对前缘气膜冷却效率影响的实验[J]. 推进技术, 2008, 29(2): 153-157. (LI Guang-chao, ZHU Hui-ren, BAI Jiang-tao, et al. Experimental Investigation of Film Cooling Effectiveness on Leading Edge with Various Geometries[J]. Journal of Propulsion Technology, 2008, 29(2): 153-157.)
[13] 胡娅萍, 吉洪湖. 孔阵排列疏密度对致密多斜孔壁冷却效果的影响[J]. 推进技术, 2005, 26(1): 28-33. (HU Ya-ping, JI Hong-hu. Effect of Porosity of Holes Array on Cooling Effectiveness of Effusion Cooling[J]. Journal of Propulsion Technology, 2005, 26(1): 28-33.)
[14] 林宇震, 李彬, 宋波, 等. 多斜孔壁冷却方式不同进气角度小孔内对流换热研究[J]. 推进技术, 1999, 20(1): 68-72. (LIN Yu-zhen, LI Bin, SONG Bo, et al. Investigation of Convective Heat Transfer Inside Small Holes with Different Inlet Angles in Inclined Multi Hole Wall Film Cooling[J]. Journal of Propulsion Technology, 1999, 20(1): 68-72.)
[15] Fric T, Campbell R, Rettig M. Quantitative Visualization of Full-Coverage Discrete-Hole Film Cooling[R]. ASME 97-GT-328.
[16] 李彬, 胡正义, 林宇震, 等. 多斜孔壁整体冷却效率实验研究[J]. 航空动力学报, 1999, 14(2): 157-160
[17] Facchini B, Coutandin D. Experimental Investigation on the Effects of a Larger Circulating Area on the Performance of an Effusion Cooling Combustor Liner[R]. ASME GT 2011-46458
[18] Andreini A, Ceccherini A, Facchini B, et al. Combined Effect of Slot Injection, Effusion Array and Dilution Hole on the Heat Transfer Coefficient of a Real Combustor Liner, Part 2: Numerical Analysis[R]. ASME GT 2010-22937
[19] 杨卫华, 卢聪明, 郑建文. 气膜一发散冷却结构冷却效果的实验研究[J]. 南京航空航天大学学报, 2014, 46(4): 517-523.
[20] Yang Weihua, Shi Xiaoxiang, Zhang Jingzhou. Experimental Investigation on Film Cooling Characteristics of Ellipse-Shaped Tab[J]. Experimental Thermal and Fluid Science, 2017, 81: 277-290.
[21] Holman J P. Experimental Methods for Engineerings[C]. New York: McGraw-hill, 1984.　　　　　　　　　　　　　*　收稿日期:2017-07-07；修订日期:2017-09-18。基金项目:国家自然科学基金(51276088)。作者简介:田美,女,硕士生,研究领域为飞机发动机热端部件冷却技术。E-mail: tianmeinuaa@163.com通讯作者:杨卫华,男,博士,教授,研究领域为飞机发动机热端部件热防护技术。E-mail: yangwh-sjtu@163.com