Experimental Study on Effects of Injection Angles on Film Cooling Performance of Sister Holes

doi:10.13675/j.cnki.tjjs.190448

Journal of Propulsion Technology ›› 2020, Vol. 41 ›› Issue (8): 1765-1772.DOI: 10.13675/j.cnki.tjjs.190448

• Combustion, Heat and Mass Transfer • Previous Articles Next Articles

Experimental Study on Effects of Injection Angles on Film Cooling Performance of Sister Holes

College of Energy and Environment,Shenyang Aerospace University,Shenyang 110136,China

Published:2021-08-15

射流角度对姊妹孔气膜冷却效果影响实验研究

李润东，李明春，贺业光，杨天华，刘学斌

沈阳航空航天大学能源与环境学院，辽宁沈阳 110136

基金资助:
国家“万人计划”科技创新领军人才（组厅字〔2016〕37号-286）；辽宁省攀登学者奖励计划。

Abstract

Abstract: To analyze the effects of the injection angles of the primary hole or the side hole on the sister hole film cooling performance of a flat plate model, pressure sensitive paint (PSP) technology was used to study the film cooling performance of a single hole and five sister holes. The results show that the sister holes had a better film cooling performance than the single hole at four blowing ratios (BR). The sister hole had a similar average spanwise film cooling efficiency at a low blowing ratio (BR=0.5). The area mean film cooling efficiency of the sister holes with the forward jet of the side hole was the highest, which were 3.66, 6.77, 7.27 times higher than the area mean film cooling efficiency of the single hole at medium blowing ratio (BR=1) and high blowing ratios (BR=1.5, 2). The film coverage of the sister holes could be increased by the backward jet, the spanwise film cooling performance of the backward sister holes could be improved by the spanwise angle of the side hole when the BR was 0.5 or 1. But the streamwise film cooling effectiveness of the sister hole decreased with the compound angle of the side hole at high blowing ratios.

Key words: Film cooling;Sister hole;Backward jet;PSP technology;Film cooling efficiency

摘要： 为了分析主孔与侧孔射流角度对逆向射流姊妹孔平板模型气膜冷却效率影响，采用压力敏感漆(PSP)技术对单孔顺流与5种姊妹孔在四种吹风比(BR)下的绝热气膜冷却效率进行研究。结果表明姊妹孔在所有吹风比下气膜冷却效果均优于单个圆孔正向射流。低吹风比(BR=0.5)时，姊妹孔气膜冷却效果相近，但顺流姊妹孔气膜冷却效果最佳；中吹风比(BR=1)、高吹风比(BR=1.5,2)下，侧孔顺流的逆向射流姊妹孔气膜冷却效果最佳，相比于单孔射流的面平均气膜冷却效率可提高366%，677%，727%。逆向射流可令姊妹孔获得更高的气膜覆盖率，具有复合角度的侧孔射流可在低、中吹风比下增加逆流姊妹孔的展向气膜覆盖率，但在高吹风比下，对姊妹孔下游流向气膜冷却效果产生较差影响。

关键词: 气膜冷却;姊妹孔;逆向射流;压力敏感漆技术;气膜冷却效率

LI Run-dong, LI Ming-chun, HE Ye-guang, YANG Tian-hua, LIU Xue-bin. Experimental Study on Effects of Injection Angles on Film Cooling Performance of Sister Holes[J]. Journal of Propulsion Technology, 2020, 41(8): 1765-1772.

李润东，李明春，贺业光，杨天华，刘学斌. 射流角度对姊妹孔气膜冷却效果影响实验研究[J]. 推进技术, 2020, 41(8): 1765-1772.

References

[1] Greber I, Kamotani Y. Experiments on a Turbulent Jet in a Cross Flow[J]. AIAA Journal， 1971， 9(11): 1451-1460.
[2] Perry A E， Kelso R M， Lim T T. Topological Structure of a Jet in a Cross Flow[C]. Winchester: AGARD-CP-534-Computational & Experimental Assessment of Jets in Cross Flow， 1993.
[3] Fric T F， Roshko A. Vortical Structure in the Wake of a Transverse Jet[J]. Journal of Fluid Mechanics， 1994， 279: 1-47.
[4] Goldstein R J， Eckert E R G， Burggraf F. Effects of Hole Geometry and Density on Three-Dimensional Film Cooling[J]. International Journal of Heat and Mass Transfer， 1974， 17(5): 595-607.
[5] Bunker R S. A Review of Shaped Hole Turbine Film- Cooling Technology[J]. Journal of Heat Transfer， 2005， 127(4): 441-453.
[6] 李雪英，韩昌，秦晏旻，等. 扇形孔气膜冷却应用的综合特性[J]. 工程热物理学报， 2013， 34(1): 55-58.
[7] 付仲议，朱惠人，刘聪，等. 涡轮导叶压力面簸箕形气膜孔冷却特性实验研究[J]. 推进技术， 2016， 37(12): 2303-2311.
[8] 韩昌. 燃气轮机高温透平气膜冷却的孔型机理及叶栅特性研究[D]. 北京：清华大学， 2014.
[9] 李广超，吴状，刘永泉，等. 孔间距对锯齿槽改善气膜冷却特性影响[J]. 推进技术， 2017， 38(5): 1065-1072.
[10] 冯红科，王春华，范芳苏，等. 椭圆槽气膜冷却结构的优化研究[J]. 推进技术， 2019， 40(5): 1099-1106.
[11] Zhou W， Hui H. Improvements of Film Cooling Effectiveness by Using Barchan Dune Shaped Ramps[J]. International Journal of Heat and Mass Transfer， 2016， 103: 443-456.
[12] Heidmann J D， Ekkad S. A Novel Anti-Vortex Turbine Film Cooling Hole Concept[J] ASME Journal Turbomachinary， 2007， 130(3).
[13] 吴宏，杨庆. 抑涡孔气膜冷却的大涡模拟[J]. 航空动力学报， 2012， 27(12): 2648-2654.
[14] Chi Zhongran， Han Chang， Li Xueying， et al. Geometrical Optimization and Experimental Validation of a Tripod Film Cooling Hole with Asymmetric Side Holes[J]. Journal of Heat Transfer， 2016， 138(6).
[15] Taeibi-Rahni M， Javadi A， Javadi K， et al. A New Approach to Improve Film Cooling Effectiveness， Using Combined Jets[C]. Tokyo： Gas Turbine Congress， 2003.
[16] Ely M J， Jubran B A. A Numerical Study on Improving Large Angle Film Cooling Performance Through the Use of Sister Holes[J]. Numerical Heat Transfer， 2009， 55(7).
[17] Ely M J， Jubran B A. A Numerical Evaluation on the Effect of Sister Holes on Film Cooling Effectiveness and the Surrounding Flow Field[J]. Heat and Mass Transfer， 2009， 45(11): 1435-1446.
[18] Hajehhasani S， Jubran B A. Numerical Assessment of the Film Cooling Through Novel Sister-Shaped Single-Hole Schemes[J]. Numerical Heat Transfer， 2015， 67(4): 414-435.
[19] Hajehhasani S， Jubran B A. A Numerical Investigation of Film Cooling Performance Through Variations in the Location of Discrete Sister Holes[J]. Applied Thermal Engineering， 2016， 107: 345-364.
[20] WU Hong， CHENG Huichuan， LI Yulong， et al. Effects of Side Hole Position and Blowing Ratio on Sister Hole Film Cooling Performance in a Flat Plate[J]. Applied Thermal Engineering， 2016， 93: 718-730.
[21] ZHU Rui， Xie Gongnan， Simon T W. New Designs of Novel Holes Based on Cylindrical Configurations for Improving Film Cooling Effectiveness [J]. Numerical Heat Transfer， Part A: Applications， 2019, 75(7).
[22] Bell J H， Schairer E T， Hand L A， et al. Surface Pressure Measurements Using Luminescent Coatings[J]. Annual Review of Fluid Mechanics， 2001， 33(1): 155-206.
[23] Rallabandi A P ， Li S J ， Han J C . Unsteady Wake and Coolant Density Effects on Turbine Blade Film Cooling Using Pressure Sensitive Paint Technique[J]. Journal of Heat Transfer， 2012， 134(8).
[24] Kline S J. Describing Uncertainty in Single Sample Experiments[J]. Mechanical Engineering， 1953， 75: 3-8.
[25] LI Mingchun， HE Yeguang， LI Rundong， et al. The Effects of Injection Angles and Aperture Ratio on the Film Cooling Performance of Sister Hole[J]. Journal of Thermal Science， 2019， 28（1）.
[26] 李佳. 燃气轮机透平气膜冷却机理的实验与理论研究[D]. 北京：清华大学， 2011.
[27] LI Guangchao， YANG Peng， ZHANG Wei， et al. Enhanced Film Cooling Performance of a Row of Cylindrical Holes Embedded in the Saw Tooth Slot[J]. International Journal of Heat and Mass Transfer， 2019， 132: 1137-1151.
[28] LIU Cunliang， ZHU Huiren， BAI Jiangtao， et al. Film Cooling Performance of Converging-Slot Holes with Different Exit-Entry Area Ratios[J]. Journal of Turbomachinery， 2010， 133(1).

Experimental Study on Effects of Injection Angles on Film Cooling Performance of Sister Holes

射流角度对姊妹孔气膜冷却效果影响实验研究

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 0

Recommended Articles

Metrics

Comments